Recent progress in passive radiative cooling technologies has substantially improved cooling performance under direct sunlight. Yet, experimental demonstrations of daytime radiative cooling still severely underperform in comparison with the theoretical potential due to considerable solar absorption and poor thermal insulation at the emitter. In this work, we developed polyethylene aerogel (PEA)—a solar-reflecting (92.2% solar weighted reflectance at 6 mm thick), infrared-transparent (79.9% transmittance between 8 and 13 μm at 6 mm thick), and low-thermal-conductivity (kPEA = 28 mW/mK) material that can be integrated with existing emitters to address these challenges. Using an experimental setup that includes the custom-fabricated PEA, we demonstrate a daytime ambient temperature cooling power of 96 W/m2 and passive cooling up to 13°C below ambient temperature around solar noon. This work could greatly improve the performance of existing passive radiative coolers for air conditioning and portable refrigeration applications.

No abstract

Demonstrations of passive daytime radiative cooling have primarily relied on complex and costly spectrally selective nanophotonic structures with high emissivity in the transparent atmospheric spectral window and high reflectivity in the solar spectrum. Here, we show a directional approach to passive radiative cooling that exploits the angular confinement of solar irradiation in the sky to achieve sub-ambient cooling during the day regardless of the emitter properties in the solar spectrum. We experimentally demonstrate this approach using a setup comprising a polished aluminum disk that reflects direct solar irradiation and a white infrared-transparent polyethylene convection cover that minimizes diffuse solar irradiation. Measurements performed around solar noon show a minimum temperature of 6 °C below ambient temperature and maximum cooling power of 45 W m–2. Our passive cooling approach, realized using commonly available low-cost materials, could improve the performance of existing cooling systems and enable next-generation thermal management and refrigeration solutions.

Recent advances in thermally localized solar evaporation hold significant promise for vapor generation, seawater desalination, wastewater treatment, and medical sterilization. However, salt accumulation is one of the key bottlenecks for reliable adoption. Here, we demonstrate highly efficient (>80% solar-to-vapor conversion efficiency) and salt rejecting (20 weight % salinity) solar evaporation by engineering the fluidic flow in a wick-free confined water layer. With mechanistic modeling and experimental characterization of salt transport, we show that natural convection can be triggered in the confined water. More notably, there exists a regime enabling simultaneous thermal localization and salt rejection, i.e., natural convection significantly accelerates salt rejection while inducing negligible additional heat loss. Furthermore, we show the broad applicability by integrating this confined water layer with a recently developed contactless solar evaporator and report an improved efficiency. This work elucidates the fundamentals of salt transport and offers a low-cost strategy for high-performance solar evaporation.

Solar steam generation at the sterilization condition suffers from low efficiency, especially in passive solar thermal devices. We developed a stationary solar collector with a transparent aerogel layer to achieve efficient solar steam generation via thermal concentration. In field tests performed in Mumbai, India, the device generated steam at 100 C with 56% efficiency and successfully powered a sterilization cycle following the standard sterilization protocol. Our work shows the potential of solar thermal technology in steam generation and other applications.

No abstract

Hydrophobic coatings with low thermal resistance promise a significant enhancement in condensation heat transfer performance by promoting dropwise condensation in applications including power generation, water treatment, and thermal management of high-performance electronics. However, after nearly a century of research, coatings with adequate robustness remain elusive due to the extreme environments within many condensers and strict design requirements needed to achieve enhancement. In this work, we enable long-lasting condensation heat transfer enhancement via dropwise condensation by infusing a hydrophobic polymer, Teflon AF, into a porous nanostructured surface. This polymer infused porous surface (PIPS) uses the large surface area of the nanostructures to enhance polymer adhesion, while the nanostructures form a percolated network of high thermal conductivity material throughout the polymer and drastically reduce the thermal resistance of the composite. We demonstrate over 700% enhancement in the condensation of steam compared to an uncoated surface. This performance enhancement was sustained for more than 200 days without significant degradation. Furthermore, we show that the surfaces are self-repairing upon raising the temperature past the melting point of the polymer, allowing recovery of hydrophobicity and offering a level of durability more appropriate for industrial applications.

Stimuli-responsive materials have been lately employed in soft robotics enabling new classes of robots that can emulate biological systems. The untethered operation of soft materials with high power light, magnetic field, and electric field has been previously demonstrated. While electric and magnetic fields can be stimulants for untethered actuation, their rapid decay as a function of distance limits their efficacy for long-range operations. In contrast, light-in the form of sunlight or collimated from an artificial source (e.g., laser, Xenon lamps)-does not decay rapidly, making it suitable for long-range excitation of untethered soft robots. In this work, an approach to harnessing sunlight for the untethered operation of soft robots is presented. By employing a selective solar absorber film and a low-boiling point (34°C) fluid, light-operated soft robotic grippers are demonstrated, grasping and lifting objects almost 25 times the mass of the fluid in a controllable fashion. The method addresses one of the salient challenges in the field of untethered soft robotics. It precludes the use of bulky peripheral components (e.g., compressors, valves, or pressurized gas tank) and enables the untethered long-range operation of soft robots.