We investigated the synthesis of amorphous aluminum titanium oxide Al1− xTi xO y thin films from a Al(acac)3 and Ti(acac)4 mixture using CH3OH/H2O as a solvent through mist chemical vapor deposition (mist-CVD) for application as a high dielectric material. The Ti composition ratio x in the Al1− xTi xO y thin films depends on the Al(acac)3 and Ti(acac)4 mixing ratios and CH3OH/H2O volume ratio. A bandgap energy of Al1− xTi xO y films was decreased from 6.38 to 4.25 eV and the surface roughness also decreased when the Ti composition ratio was increased from 0 to 0.54. The capacitance–voltage plot revealed that the dielectric constant of Al1− xTi xO y thin films increased from 6.23 to 25.12. Consequently, Al1− xTi xO y thin films with a bandgap energy of 5.12 eV and a dielectric constant of 13.8 were obtained by adjusting the ratio x of 0.26. This Al0.74Ti0.26O y layer was applied as a gate dielectric layer for metal-oxide-semiconductor field-effect transistors (MOSFETs) using a mechanically exfoliated two-dimensional (2D) transition metal dichalcogenide (TMDC), MoSe2, and As-doped WSe2 flakes as a channel layer. The MoSe2-based MOSFETs with source/drain gold electrodes exhibit n-channel behavior with a field-effect mobility of 85 cm2/(V s), a threshold voltage of 0.92 V. On the other hand, an on/off ratio of ∼106. As-doped WSe2-based MOSFETs with source/drain platinum electrodes also showed an ambipolar behavior, which was applied for use in logic applications. These findings suggest that Al0.74Ti0.26O y by mist-CVD is promising as a high- k material for TMDC-based MOSFETs.
Aluminum oxide (AlOx) thin films were grown using aluminum acetylacetonate [Al(acac)3] as a source material with methanol and water as the solvent by mist chemical vapor deposition, while also exposing some films to water or methanol mists after fabrication. The incorporation of –OH groups into the AlOx network that is fabricated from Al(acac)3 and using solely methanol as a solvent generates both malformed Al(OH) network and nonuniformity. However, the addition of a small amount of water in the solvent during film growth decreases the deposition rate due to the hydrogen bond in water molecules but markedly removes –OH groups from the growth surface of the AlOx network and improves the surface uniformity. The AlOx thin films grown with a methanol:water ratio of 7:3 at 400 °C exhibit a recombination velocity of 16 cm/s, a breakdown field of 6.9 MV/cm, and an interface trap density of 4.2 × 1010 cm−2 eV−1, which are compatible with the AlOx grown by the other vacuum-based methods.
Molybdenum disulfide (MoS2) mono/bilayer have been systematically investigated using atmospheric-pressure mist chemical vapor deposition (mist CVD) from (NH4)2MoS4 dissolved in N-methyl-2-pyrrolidone as a precursor. Film deposition was performed by alternating MoS2 mist storage within a closed chamber and mist exhaust, i.e. sequential mist supply mode at different furnace temperatures, storage times of precursor, and repetition cycles of mist supply on thermally grown SiO2 (th-SiO2) and mist-CVD grown Al1−x Ti x O y (ATO) layers coated on p+-Si substrates. The average size of the MoS2 flake and their number of stack layers could be controlled by tuning the deposition parameters combined with substrate pretreatment. Field-effect transistors with MoS2 atomic mono/bilayer as a channel layer exhibited mobility up to 31–40 (43–55) cm2 V−1 s−1 with a threshold voltage of −1.6 (−0.5) V, subthreshold slope of 0.8 (0.11) V dec.−1, and on/off ratio of 3.2 × 104 (3.6 × 105) on th-SiO2 (ATO) layers as gate dielectric layers without mechanical exfoliation. These findings imply that mist CVD is available for the synthesis of metal transition metal dichalcogenide and metal oxide layers as channel and gate dielectric layers, respectively.
We investigated the synthesis of aluminum oxide (AlO x ) thin films using mist chemical vapor deposition (mist-CVD) from aluminum acetylacetonate (Al(acac)3) and methanol/water (MeOH/H2O) mixture (volume ratio, 7:3). Different deposition parameters, such as the flow rate (F d) of dilution gas N2, furnace temperature (T f), solution concentration, and mesh bias (V m), were optimized via the analysis of the size distribution of mist precursors using a fast-scanning mobility particle analyzer. The film morphology, rigidity of the AlO x network, and junction property at the AlO x /n-type crystalline Si (n-Si) were dominated by the size distribution of the mist precursors determined by the deposition parameters. Further, the mesh bias supply during film growth promoted the miniaturization of the size distribution of the charged mist particles. Consequently, a marked increase in the number density of the mist particles resulted in an increased refractive index (n) of the AlO x thin films with small surface roughness values. Furthermore, such property of the AlO x films improved the junction property at the AlO x /n-Si interface. In this study, the correlation between the size distribution of mist particles, which is dependent on the deposition parameters, and the film and interface properties, is presented together with metal-oxide–semiconductor field-effect transistor (MOS-FET) performance for the AlO x thin films obtained by mist-CVD.
We have investigated an n-type crystalline Si (n-Si) heterojunction solar cell with organic conductive polymer poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) on a plane and isotropically textured n-Si substrate by using chemical mist deposition (CMD). The PEDOT:PSS layer was deposited uniformly on isotropically textured n-Si with the increased passivation of surface defects of n-Si and stronger adhesion rather than the spin-coated film by adjusting deposition parameters. The power conversion efficiency increased from 12.5% on plane n-Si to 16%–18.2% for both CMD coated front- and back-PEDOT:PSS/n-Si junction solar cells on the 2 × 2 cm2-sized isotropically textured substrate by combining with a 1–2-nm-thick Ba(OH)2 by CMD as a hole-blocking layer at the Al/n-Si interface. These findings originate from the increased passivation of surface dangling bonds of isotropically textured n-Si, resulting in strong inversion of the n-Si surface to p-type Si by the polymer.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.