Potential and utilization of renewable energy in Indonesia is still very small. Oneof the renewable energy sources is wind energy. The use of wind turbines, windenergy is converted into mechanical energy and can then generate electricitythrough a generator. Wind turbines are environmentally friendly, inexpensive,easy to operate and easy to maintain. The purpose of this study was to determinethe effect on the performance of the number of blades and wind speed for thevertical axis wind turbine type darrieus H with the NACA profile 3412 with apitch 0o angle. This study uses an experimental method, with a number of bladesand varying wind speeds. The number of blades given is 2 units, 3 units and 4units. The speed of the given wind is 3.3 m / s, 3.5 m / s, 3.7 m / s, and 3.9 m / s.Performance is obtained from the electrical power produced by a generatormounted on the turbine axis. The results showed that the turbine performance wasinfluenced by the number of blades. The highest power in the number of bladeswas 4 units at a wind speed of 3.3 m / s which resulted in electric power of 5.166Watt. The lowest electric power is produced on turbines with a number of units of2 units at a wind speed of 3.3 m / s, which is 3.0173 Watts. The blade is 2 unitsand 3 units, at a wind speed of 3.3 m / s; 3.5 m / s; 3.7 m / s and 3.9 m / s, theelectrical power produced is relatively the same, while in blades 4 units, thedifference in wind speed (3.3 m / s; 3.5 m / s; 3.7 m / s and 3.9 m / s) produce adifference in the electrical power produced
Heat pipe merupakan salah satu alat penukar kalor yang memungkinkan pemindahan sejumlah kalor melalui luas permukaan yang sangat kecil. Heat Pipe mempunyai peran penting dalam sistem pendinginan salah satunya dalam komponen elektronika. Dengan sistem pendinginan maka temperatur komponen akan terjaga sehingga terhindar dari kerusakan kerusakan yang diakibatkan dari panas yang berlebih (over heating). Heat pipe terdiri dari tiga bagian, yaitu evaporator, adiabatis dan kondensor. Kedalam pipa itu diberi fluida kerja yang berfungsi membawa panas dari evaporator dan melepaskannya di kondensor. Di bagian Evaporator, panas dari komponen yang didinginkan diserap dan dipindahkan ke ujung yang lain yaitu bagian Kondensor untuk dilepas panasnya dilingkungan. Heat pipe mempunyai prinsip yang hampir sama dengan thermosyphon, perbedaannya adalah di heat pipe menggunakan dinding wick. Kegiatan penelitian ini bertujuan mengetahui sejauh mana kinerja termal dari heat pipe sebagai penukar kalor dengan variasi panjang kondensor. Heat Pipe didesain dengan variasi panjang kondensor sebesar 44 cm ,66 cm,88 cm,110 cm dan 132 cm.. Hasil penelitian menunjukkan bahwa, Tahanan thermal tertinggi pada panjang kondensor terpendek pada tempeatur 400C (14 C/W) dan terendah pada panjang kondensor terpanjang pada temperatur 1200 C(1 C/W). Pada semua temperatur, semua variasi panjang kondensor maka daya output dan fluks kalor akan semakin besar. Pada panjang kondensor ukuran yang sama dengan evaporator, semakin tinggi temperatur, maka semakin besar fluks kalor dan daya output. Proses pada eksperimen ini paling efektif pada panjang kondensor 1,25 kali (132 cm) dari panjang panjang evaporator, karena setelahnya nilai tahanan termal dan daya output akan mengalami kecernderungan tetap.
Pengabdian kepada masyarakat (PkM) ini dilaksanakan pada Karang Taruna yang terletak di Kelurahan Srengat Kecamatan Srengat Kabupaten Blitar. Permasalahan pada Karang Taruna ini adalah, banyak anggota Karang Taruna yang masih belum mendapatkan pekerjaan yang tetap, banyak yang menganggur, terkadang kerja terkadang berhenti, belum mengenyam pendidikan tinggi dan tidak mempunyai pengetahuan serta ketrampilan yang dapat digunakan sebagai nilai jual bekerja baik wirausaha ataupun bekerja di bengkel/perusahaan. Solusi untuk memecahkan permasalahan yaitu melalui beberapa kegiatan, antara lain: pelatihan teori pengelasan dan pelatihan praktek pengelasan SMAW dengan membuat rak bunga. PkM ini ini mempunyai tujuan untuk meningkatkan ketrampilan pengelasan SMAW pembuatan rak bunga. Luaran dari PkM ini adalah kegiatan pelatihan pengelasan SMAW dan bantuan unit pengelasan kepada Karang Taruna yang dapat digunakan untuk latihan dan untuk kelengkapan kegiatan karang taruna. Materi pelatihan meliputi K3 dalam pengelasan, dasar dasar pengelasan dan pengelasan SMAW Kesimpulan yang diperoleh selama program kegiatan PkM ini adalah adanya peningkatan pengetahuan dan ketrampilan remaja karang taruna tentang pengelasan SMAW pembuatan rak bunga sehingga mendapatkan bekal yang cukup sebagai modal kerja atau berwirausaha.
Metode perawatan ISMO merupakan metode perawatan yang dilakukan pada saat performa mesin sudah mulai menurun, histori dari mesin terbatas dan kurangnya informasi dengan manual book. Metode ini menggunakan acuan derajat kerumitan untuk menentukan penjadwalannya. Metode perawatan ini diterapkan pada turbin tipe vertikal Francis kapasitas 35 MW. Tujuan dari penelitian ini adalah untuk mendapatkan informasi perawatan yang berupa jadwal perawatan dan estimasi biaya perawatan dari turbin tipe vertical francis kapasitas 35 MW. Dari penelitian ini dihasilkan jadwal perawatan secara komperehensif dan besaran biaya yang dibutuhkan mulai dari kegiatan inspeksi, small repair, medium repair dan overhoule beserta besaran biaya . Dalam satu siklus, kegiatan inspeksi dilakukan sebanyak 9 kali, medium repair 6 kali dan overhoule 1 kali. Total biaya yang dibutuhkan untuk melakukan perawatan turbin tipe vertical francis dalam jangka waktu 3 tahun adalah sebesar Rp. 97.937.000,-
Perguruan Tinggi mempunyai peran penting dalam Tri Darma, yaitu ikut dalam mencerdaskan kehidupan bangsa dan negara sencara nyata di masyarakat. Salah satu langkahnya adalah menjadikan manusia bukan lagi menjadi obyek pembangunan tetapi menjadi subyek pembangunan. Sebagai subyek pembangunan tentunya diperlukan kemampuan dan kecakapan dalam penguasaan ilmu pengetahuan dan teknologi. Pemanfaatan teknologi pengelasan telah berkembang dan banyak digunakan dan dimanfaatkan ditengah masyarakat luas, baik untuk skala industri rumah tangga maupun untuk perbaikan perbaikan peralatan dirumah. Salah satu metode pengelasan adalah pengelasan SMAW, yaitu pengelasan dengan menggunakan busur listrik.Tujuan dari kegiatan ini adalah meningkatkan pengetahuan secara umum remaja karang taruna kelurahan Temas Kecamatan Batu kota Batu, menambah ketrampilan kusus berupa pengelasan SMAW dan memberikan dorongan dan bantuan sehingga karang taruna kampung teh mampu mengadakan peralatan las.Manfaat dari kegiatan ini adalah memberikan pengetahuan dan melatih ketrampilan dalam pengelasan SMAW sehingga bisa digunakan untuk pengembangan pribadi maupun manfaat secara sosial
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.