We describe the modification of indium-tin oxide (ITO) electrodes via the chemisorption and electropolymerization of 6-{2,3-dihydrothieno[3,4-b]-1.4-dioxyn-2-yl methoxy}hexanoic acid (EDOTCA) and the electrochemical co-polymerization of 3,4-ethylenedioxythiophene (EDOT) and EDOTCA to form ultrathin films that optimize electron-transfer rates to solution probe molecules. ITO electrodes were first activated using brief exposure to strong haloacids, to remove the top approximately 8 nm of the electrode surface, followed by immediate immersion into a 50:50 EDOT/EDOTCA co-monomer solution. Potential step electrodeposition for brief deposition times was used to grow copolymer films of thickness 10-100 nm. The composition of these copolymer films was characterized by solution depletion studies of the monomers and atomic force microscopy (AFM), X-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy (reflection-absorption infrared spectroscopy (RAIRS)) of the product films. The spectroscopic data suggest that the composition of the copolymer approaches 80% EDOTCA when electropolymerization occurs from concentrated (10 mM) solutions. AFM characterization shows that electrodeposited poly(EDOT)/poly(EDOTCA) (PEDOT/PEDOTCA) films are quite smooth, with texturing on the nanometer scale. RAIRS studies indicate that these films consist of a combination of EDOTCA units with noninteracting -COOH groups and adjacent hydrogen-bonded -COOH groups. The EDOTCA-containing polymer chains appear to grow as columnar clusters from specific regions, oriented nearly vertically to the substrate plane. As they grow, these columnar clusters overlap to form a nearly continuous redox active polymer film. ITO activation and formation of these copolymer films enhances the electroactive fraction of the electrode surface relative to a nonactivated, unmodified "blocked" ITO electrode. Outer-sphere solution redox probes (dimethylferrocene) give standard rate coefficients, kS > or = 0.4 cm.s-1, at 10 nm thick copolymer films of PEDOT/PEDOTCA, which is 3 orders of magnitude greater than that on the unmodified ITO surface and approaches the values for kS seen on clean gold surfaces.

The acid dissociation constant in water for a monorhamnolipid mixture extracted from Pseudomonas aeruginosa ATCC 9027 has been determined using potentiometry and two spectroscopic approaches at concentrations below and above the critical micelle concentration (cmc). Potentiometric titrations resulted in pKa values ranging from 4.28 +/- 0.16 to 5.50 +/- 0.06 depending on concentration. 1H NMR spectrochemical titrations at concentrations below the cmc revealed a pKa value of 4.39 +/- 0.06. ATR-FT-IR spectrochemical titrations on solutions well above the cmc gave a pKa value of 4.84 +/- 0.05. The value of 4.28 for the free rhamnolipid molecule for concentrations below the cmc differs markedly from that reported previously. However, the pKa of 5.50 for surface-adsorbed and solution aggregates correlates closely to that previously reported. Differences in these pKa values are rationalized in terms of the pH- and concentration-dependent aggregation behavior of rhamnolipids in aqueous solution.

Viscosin (1), an effective surface-active cyclic lipopeptide, was efficiently recovered from Pseudomonas libanensis M9-3 with a simple purification protocol. A major pigment also obtained during this process was identified as phenazine-1-carboxylic acid. The critical micelle concentration (cmc) of viscosin was determined to be 54 mg L (-1), and the minimum surface tension between air and water at the cmc was 28 mN m (-1). Viscosin forms stable emulsions even at low concentrations (7.5 mg L (-1)), and the conditional stability constant for a cadmium-viscosin complex was determined to be 5.87. The physicochemical properties measured for viscosin are similar to other well-studied biosurfactants such as rhamnolipid and surfactin. Viscosin inhibited migration of the metastatic prostate cancer cell line, PC-3M, without visible toxicity. These properties suggest the potential of viscosin in environmental and biomedical applications.