No abstract

The effect of staining and vacuum sintering on optical properties and the bi-axial flexural strength of partially and fully stabilized monolithic zirconia (PSZ, FSZ) were evaluated. Disc-shaped specimens divided into three subgroups (n=15): non-stained, stained and non-stained with vacuum sintering. After staining and sintering, optical properties were evaluated using a reflection spectrophotometer and bi-axial flexural strength was tested using the piston-on-three balls technique. Statistical analysis was performed using multivariate analysis of variance (MANOVA) followed by post-hoc Tukey's tests (p<0.05). Staining decreased translucency parameter (TP) values of FSZ (p<0.05). Sintering under vacuum enhanced TP values for PSZ (p<0.05). Staining enhanced surface gloss for both types of zirconia (p<0.05). Staining increased bi-axial flexural strength of FSZ (p<0.05), while it decreased the strength of PSZ (p<0.05). Sintering under vacuum provided minimal benefits with either type of zirconia.

BackgroundWhen implants are restored with cement-retained restorations, prosthetic retrievability can be difficult and often requires sectioning using rotary instruments. Sometimes repeated removals of a cement-retained implant crown are needed such as for treatment of peri-implantitis or immediate implant provisionalization. The purpose of this study was to evaluate the effect of erbium-doped yttrium aluminum garnet (Er:YAG) laser as a non-invasive treatment modality to remove lithium disilicate crowns from zirconia implant abutments following long-term cementation, repetitive debonding and re-cementation, and short-term retrieval.Material and methodsTwenty identical lithium disilicate crowns were cemented onto zirconia prefabricated abutments using composite resin cement. Ten cemented crowns were removed at 48 hours after cementation as a short-term group (ST), while another 10 were removed 6 months after cementation as a long-term group (LT). To mimicking repetitive recementation and retrieval, the LT crowns were then recemented and removed after 48 hours as a long-term recemention (LTR) group. The LTR crowns were then again recemented and removed after 48 hours as a long-term repeated recemention (LTRR) group. Er:YAG laser was used to facilitate the retrieval of these crowns. recorded and analyzed using ANOVA and t-test. The surfaces of the crown and the abutment were further examined using light microscopy and scanning electron microscopy (SEM). Temperature changes of the abutment and crown upto 10 minutes were also measured and statistically analyzed (paired t-test).ResultsThe average times of crown removal from zirconia abutments were 4 minutes (min) and 42 second (sec) in LT to 3 min 24 sec in LTR, and 3 min 12 sec in LTRR and ST groups. LTR took the longest time to remove, statistically (ANOVA and t-test, p < .001). No statistical differences were observed among the removal times of LTR, LTRR, and ST groups (t-test, p = .246, .246 and 1). SEM examination of the material surface showed no visual surface damaging from treatment with Er:YAG laser. The temperatures during irradiation ranged from 18.4°C to 20°C and 22.2°C to 24.5°C (Paired t-test, p < .0001) for the abutment and the crown during irradiation from 1 min to 10 mins.ConclusionsLong-term cementation can increase time in lithium disilicate crown removal from zirconia abutment using Er:YAG. Er:YAG laser is a non-invasive tool to remove cement-retained implant prostheses and should be considered as a viable alternative to rotary instruments.

No abstract

No abstract

No abstract

Background Removal of cement-retained implant fixed restorations when needed, can be challenging. Conventional methods of crown removal are time consuming and costly for patients and practitioners. This research explored the use of two different types of pulsed erbium lasers as a non-invasive tool to retrieve cemented zirconia crowns from zirconia implant abutments. Materials and methods Twenty identical zirconia crowns were cemented onto 20 identical zirconia prefabricated abutments using self-adhesive resin cement. The specimens were divided into two groups for laser assisted crown removal; G1 for erbium-doped yttrium aluminum garnet laser (Er: YAG), and G2 for erbium, chromium-doped yttrium, scandium, gallium and garnet (Er,Cr: YSGG). For the G1, after the first crown removal, the specimens were re-cemented and removed again using the Er:YAG laser. Times needed to remove the crowns were recorded and analyzed using ANOVA (α = 0.05). The surfaces of the crown and the abutment were further examined using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) analyses. Results The average times of zirconia crown removal from zirconia abutments were 5 min 20 sec and 5 min 15 sec for the Er:YAG laser of first and second experiments (G1), and 5 min 55 sec for the Er,Cr:YSGG laser experiment (G2). No statistical differences were observed

No abstract