Flexible pressure sensors have many potential applications in wearable electronics, robotics, health monitoring, and more. In particular, liquid-metalbased sensors are especially promising as they can undergo strains of over 200% without failure. However, current liquid-metal-based strain sensors are incapable of resolving small pressure changes in the few kPa range, making them unsuitable for applications such as heart-rate monitoring, which require a much lower pressure detection resolution. In this paper, a microfluidic tactile diaphragm pressure sensor based on embedded Galinstan microchannels (70 µm width × 70 µm height) capable of resolving sub-50 Pa changes in pressure with sub-100 Pa detection limits and a response time of 90 ms is demonstrated. An embedded equivalent Wheatstone bridge circuit makes the most of tangential and radial strain fields, leading to high sensitivities of a 0.0835 kPa −1 change in output voltage. The Wheatstone bridge also provides temperature self-compensation, allowing for operation in the range of 20-50 °C. As examples of potential applications, a polydimethylsiloxane (PDMS) wristband with an embedded microfluidic diaphragm pressure sensor capable of real-time pulse monitoring and a PDMS glove with multiple embedded sensors to provide comprehensive tactile feedback of a human hand when touching or holding objects are demonstrated.

Figure 1: We present a computational framework to generate ribs to enhance the structural strength and stiffness of a shell (a). Our ribreinforced shell structure (c) costs the same amount of material as a pure shell without any ribs (a), while achieving much better mechanical performance. And (b) and (d) are coloring visualizations of the magnitude of von Mises stress of (a) and (c), respectively, under the same load and boundary conditions. Warmer color represents higher stress and red encodes stress exceeding the yield strength 42 MPa. The maximum stress in (b) is 109.84 MPa, which far exceeds 42 MPa, while the maximum stress in (d) is below 40 MPa with the contribution from ribs. The maximum stress of the shell is about 3 times of the stress of the rib-reinforced shell structure, indicating the latter achieves much higher strength than the former. We also fabricated the two structures by 3D printing and made a stiffness comparison as shown in Figure 19 which indicates much higher stiffness of the rib-reinforced shell structure. AbstractShell structures are extensively used in engineering due to their efficient load-carrying capacity relative to material volume. However, large-span shells require additional supporting structures to strengthen fragile regions. The problem of designing optimal stiffeners is therefore becoming a major challenge for shell applications. To address it, we propose a computational framework to design and optimize rib layout on arbitrary shell to improve the overall structural stiffness and mechanical performance. The essential of our method is to place ribs along the principal stress lines which reflect paths of material continuity and indicates trajectories of internal forces. Given a surface and user-specified external loads, we perform a Finite Element Analysis. Using the resulting principal stress field, we generate a quad-mesh whose edges align with this cross field. Then we extract an initial rib network from the quad-mesh. After simplifying rib network by removing ribs with little contribution, we perform a rib flow optimization which allows ribs to swing on surface to further adjust rib distribution. Finally, we optimize rib cross-section to maximally reduce material usage while achieving certain structural stiffness requirements. We demonstrate that our rib-reinforced shell structures achieve good static performances. And experimental results by 3D printed objects show the effectiveness of our method.

No abstract

Facial Animation is a serious and ongoing challenge for the Computer Graphic industry. Because diverse and complex emotions need to be expressed by different facial deformation and animation, copying facial deformations from existing character to another is widely needed in both industry and academia, to reduce time-consuming and repetitive manual work of modeling to create the 3D shape sequences for every new character. But transfer of realistic facial animations between two 3D models is limited and inconvenient for general use. Modern deformation transfer methods require correspondences mapping, in most cases, which are tedious to get. In this paper, we present a fast and automatic approach to transfer the deformations of the facial mesh models by obtaining the 3D point-wise correspondences in the automatic manner. The key idea is that we could estimate the correspondences with different facial meshes using the robust facial landmark detection method by projecting the 3D model to the 2D image. Experiments show that without any manual labelling efforts, our method detects reliable correspondences faster and simpler compared with the state-of-the-art automatic deformation transfer method on the facial models.

Since non-automatic rigging requires heavy human involvements, and various automatic rigging algorithms are less efficient in terms of computational efficiency, especially for current curve-based skin deformation methods, identifying the iso-parametric curves and creating the animation skeleton requires tedious and time-consuming manual work. Although several automatic rigging methods have been developed, but they do not aim at curve-based models. To tackle this issue, this paper proposes a new rigging algorithm for automatic generation of dynamic skin deformation to quickly identify iso-parametric curves and create an animation skeleton in a few milliseconds, which can be seamlessly used in curve-based skin deformation methods to make the rigging process fast enough for highly efficient computer animation applications.