New amphiphilic block copolymers S nSz m consisting of blocks with varied degrees of polymerization, n and m, of polystyrene, S, and polystyrene carrying an amphiphilic polyoxyethylene-polytetrafluoroethylene chain side-group, Sz, were prepared by controlled atom transfer radical polymerization (ATRP). The block copolymers, either alone or in a blend with commercial SEBS (10 wt% SEBS), were spin-coated in thinner films (200-400 nm) on glass and spray-coated in thicker films ( approximately 500 nm) on a SEBS underlayer (150-200 microm). Angle-resolved X-ray photoelectron spectroscopy (XPS) measurements proved that at any photoemission angle, varphi, the atomic ratio F/C was larger than that expected from the known stoichiometry. Consistent with the enrichment of the outer film surface (3-10 nm) in F content, the measured contact angles, theta, with water (theta w > or = 107 degrees ) and n-hexadecane (theta h > or = 64 degrees ) pointed to the simultaneous hydrophobic and lipophobic character of the films. The film surface tension gamma S calculated from the theta values was in the range 13-15 mN/m. However, the XPS measurements on the "wet" films after immersion in water demonstrated that the film surface underwent reconstruction owing to its amphiphilic nature, thereby giving rise to a more chemically heterogeneous structure. The atomic force microscopy (AFM) images (tapping mode/AC mode) revealed well-defined morphological features of the nanostructured films. Depending on the chemical composition of the block copolymers, spherical (ca. 20 nm diameter) and lying cylindrical (24-29 nm periodicity) nanodomains of the S discrete phase were segregated from the Sz continuous matrix (root-mean-square, rms, roughness approximately 1 nm). After immersion in water, the underwater AFM patterns evidenced a transformation to a mixed surface structure, in which the nanoscale heterogeneity and topography (rms = 1-6 nm) were increased. The coatings were subjected to laboratory bioassays to explore their intrinsic ability to resist the settlement and reduce the adhesion strength of two marine algae, viz., the macroalga (seaweed) Ulva linza and the unicellular diatom Navicula perminuta. The amphiphilic nature of the copolymer coatings resulted in distinctly different performances against these two organisms. Ulva adhered less strongly to the coatings richer in the amphiphilic polystyrene component, percentage removal being maximal at intermediate weight contents. In contrast, Navicula cells adhered less strongly to coatings with a lower weight percentage of the amphiphilic side chains. The results are discussed in terms of the changes in surface structure caused by immersion and the effects such changes may have on the adhesion of the test organisms.

No abstract

In this paper, the interaction between cobalt oxides (Co3O4 and CoO) and methanol is studied. CoO was obtained by heating under high-vacuum (HV) conditions and characterized by X-ray photoelectron spectroscopy (XPS). The Co3O4 powder sample was characterized by means of XPS, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, X-ray diffraction (XRD), and thermal analysis. The interaction between Co3O4 and methanol was studied both at atmospheric pressure (by means of DRIFT spectroscopy) and under HV conditions (by means of XPS and quadrupolar mass spectroscopy, QMS), whereas the chemisorption of methanol on the CoO surface was studied only under HV conditions. Methanol chemisorbs mainly molecularly on the cobalt oxide surfaces, the alcohol dissociation being more evident at higher temperatures. In the case of Co3O4, the formation of formate and polymers of formaldehyde is evident around 473−523 K, whereas under HV conditions, formaldehyde and several decomposition and fragmentation products were observed as well as carbon oxides. Similar results were obtained in the case of CoO.

Amphiphilic diblock copolymers, Sz6 and Sz12, consisting of a poly(dimethylsiloxane) block (average degree of polymerisation ¼ 132) and a PEGylated-fluoroalkyl modified polystyrene block (Sz, average degree of polymerisation ¼ 6, 12) were prepared by atom transfer radical polymerization (ATRP). Coatings were obtained from blends of either block copolymer (1-10 wt%) with a poly(dimethylsiloxane) (PDMS) matrix. The coating surface presented a simultaneous hydrophobic and lipophobic character, owing to the strong surface segregation of the lowest surface energy fluoroalkyl chains of the block copolymer. Surface chemical composition and wettability of the films were affected by exposure to water. Block copolymer Sz6 was also blended with PDMS and a 0.1 wt% amount of multiwall carbon nanotubes (CNT). The excellent fouling-release (FR) properties of these new coatings against the macroalga Ulva linza essentially resulted from the inclusion of the amphiphilic block copolymer, while the addition of CNT did not appear to improve the FR properties.

A series of diblock copolymers prepared from styrenic monomers was synthesized using atom transfer radical polymerization. One block was derived from styrene, whereas the second block was prepared from a styrene modified with an amphiphilic PEGylated‐fluoroalkyl side chain. The surface properties of the resulting polymer films were carefully characterized using dynamic contact angle, XPS, and NEXAFS measurements. The polymer morphology was investigated using atomic force microscope and GISAXS studies. The block copolymers possess surfaces dominated by the fluorinated unit in the dry state and a distinct phase separated microstructure in the thin film. The microstructure of these polymers is strongly influenced by the thin film structure in which it is investigated. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 267–284, 2009

La0.6Sr0.4Co1−y FeyO3−δ (y = 0.2, 0.5, 0.8) perovskite-type oxide powders were prepared by the citrate gel method with the aim of investigating the influence of cobalt/iron atomic ratio on the chemical and structural properties as well as on the catalytic activity. The samples were characterized by means of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), thermal analysis, Kr physisorption surface area, scanning electron microscopy (SEM), and temperature programmed reduction (TPR). XRD outcomes reveal the formation of perovskite phase after calcination at 873 K. Depending on the Co/Fe atomic ratio, the perovskite exhibits two different structure: rhombohedral for y < 0.5, orthorhombic for y ≥ 0.5. However, other phases are also observed. The crystallite size increases with the calcination temperature, while decreases with the iron content. The specific surface area of the La0.6Sr0.4Co1−y FeyO3-δ perovskites (calcined at 1073 K) is low, but increases with the iron amount: it varies between 4.1 and 6.6 m2 g−1 moving from y = 0.2 to y = 0.8. XPS results reveal the presence of traces of Co(II) in the sample with lower cobalt amount. The scanning electron micrographs reveal nanoscaled near spherical particles which are clustered together, forming a highly porous microstructure. However, the samples with higher iron content show a more compact morphology due to the enhanced agglomeration. The perovskite phase is rather stable even after aggressive treatment as high temperature reduction. The influence of cobalt/iron atomic ratio on the catalytic activity toward alcohol steam reforming was investigated. All the samples present good alcohol dehydrogenation activity, as resulting from the methanol steam reforming experiments. In the steam reforming of ethanol, the La0.6Sr0.4Co0.5Fe0.5O3-δ presents the better performance (especially after reduction at 873 K) with the complete conversion of ethanol into syngas above 850 K and the almost complete suppression of the ethylene formation at lower temperature. The differences of the activity toward ethanol steam reforming are attributable to a different stabilization of Co(0) nanoparticles produced during the reduction at 873 K.

No abstract

No abstract