A series of biobased epoxy monomers were prepared from diphenolic acid (DPA) by transforming the free acid into n-alkyl esters and the phenolic hydroxyl groups into diglycidyl ethers. NMR experiments confirmed that the diglycidyl ethers of diphenolates (DGEDP) with methyl and ethyl esters have 6 and 3 mol % of glycidyl ester. Increasing the chain length of DGEDP n-alkyl esters from methyl to n-pentyl resulted in large decreases in epoxy resin viscosity (700-to-11 Pa•s). Storage modulus of DPA epoxy resins, cured with isophorone diamine, also varied with n-alkyl ester chain length (e.g., 3300 and 2100 MPa for the methyl and n-pentyl esters). The alpha transition temperature of the cured materials showed a linear decrease from 158 to 86 °C as the ester length increases. The Young's modulus and tensile strengths were about 1150 and 40 MPa, respectively, for all the cured resins tested (including DGEBA) and varied little as a function of ester length. Degree of cure for the different epoxy resins, determined by FTIR and DSC, closely approached the theoretical maximum. The result of this work demonstrates that diglycidyl ethers of n-alkyl diphenolates represent a new family of biobased liquid epoxy resins that, when cured, have similar properties to those from DGEBA.

Cellulose nanocrystals (CNCs) were modified with natural di-and tricarboxylic acids using two concurrent acid-catalyzed reactions including hydrolysis of amorphous cellulose segments and Fischer esterification, resulting in the introduction of free carboxylic acid functionality onto CNC surfaces. CNC esterification was characterized by Fourier Transform Infrared Spectroscopy, 13 C solid state magic-angle spinning (MAS) and conductometric titration experiments. Average degree of substitution values for malonate, malate, and citrate CNCs are 0.16, 0.22 and 0.18, respectively. Despite differences in organic acid pKa, optimal HCl cocatalyst concentrations were similar for malonic, malic and citric acids. After isolation of modified CNCs, residual cellulose co-products were identified that are similar to microcrystalline cellulose based on SEM and XRD analysis. As proof of concept, recycling experiments were carried to increase the yield of citrate CNCs. The by-product was then recycled by subsequent citric acid/HCl treatments that resulted in 55% total yield of citrate CNCs.The crystallinity, morphology, and substitution of citrate CNCs from recycled cellulose coproduct is similar to modified citrate CNCs formed in the first reaction cycle. Thermal stability of all modified CNCs under air and nitrogen resulted in T 10% and T 50% values above 256 °C and 323 °C, respectively. Thus, they can be used for melt-processing operations performed at moderately high temperatures without thermal decomposition. Nanocomposites of polyvinyl alcohol with modified CNCs (1 wt% malonate-, malate-, citrate and unmodified CNCs) wereprepared. An increase in the thermal decomposition temperature by almost 40 °C was obtained for PVOH-citrate modified CNC nanocomposites.Furthermore, since TGA determined weight loss up to 150°C is attributed to loss of bound water, this provides a tool to determine CNC water affinity. By 150°C, the weight loss of modified and non-modified CNCs is 6% and 2%, respectively. Consequently, modified CNCs with surface carboxylate groups have higher water affinity than non-modified CNCs. Moreover, significant differences in the thermal stability are observed as a function of the di-or triacid used for CNC modification. Based on the peaks of the derivative thermogravimetric curve (DTG, T 50% ), modified CNCs have the following thermal stability: malonate = HCl > malate > citrate CNCs.Corresponding values for T 50% are 366°C, 365°C, 350°C and 345°C, respectively. The amount of residual char at 600°C for HCl, malonate, malate and citrate CNCs is 8, 13, 16 and 20%, respectively. Hence, it follows that increasing the T 50% for di-and tri-acid modified CNCs results in correspondingly lower char formation. Increased char amounts is likely due to CNC functionalizations that lead to relatively larger number of cross-linking events at elevated temperatures.Since the exclusion of air during melt processing is generally not practical, the effect of CNC modification on thermal stability in air was also determined and the correspo...

No abstract

In this work, a series of bio-based chemically recyclable epoxy resins were synthesized from n-alkyl bisferulate esters that do not activate human estrogen receptor alpha (ERα).