No abstract

No abstract

A nickel alloy of a composition similar to that of the nickel based superalloy Inconel alloy 718 (IN718) was produced with the electron beam melting (EBM) process developed by Arcam AB. The microstructures of the as processed and heat treated material are similar to that of conventionally produced IN718, except that the EBM material showed some porosity and the δ phase did not dissolve during the solution heat treatment because the temperature of 1000°C apparently was too low. Mechanical testing of the layer structured material, parallel and perpendicular to the built layers, revealed sufficient strength in both directions. However, it showed only limited elongation when tested perpendicular to the built layers due to local agglomerations of pores. Otherwise, data for the hardness, Young's modulus, 0·2 yield tensile strength and ultimate tensile strength match those recommended for IN718.

No abstract

No abstract

Since there is no report on the influence of machining depth on electron beam melting (EBM) parts, this paper investigated the role of superficial defects and machining depth in the performance of EBM made Inconel 718 (IN718) samples. Therefore, as-built EBM samples were analyzed against the shallow-machined (i.e., only removal of outer surfaces) and deep-machined (i.e., deep surface removal into the material) parts. It was shown that both as-built and shallow-machined samples had a drastically lower yield strength (970 ± 50 MPa), ultimate tensile stress (1200 ± 40 MPa), and ductility (28 ± 2%) compared to the deep-machined samples. This was since premature failure occurred due to various superficial defects. The superficial defects appeared in two levels, as (1) notches and pores on the surface and (2) irregular pores and cracks within the subsurface. Since the latter occurred down to 2 mm underneath the surface, shallow machining only exposed the subsurface defects to outer surfaces. Thus, the shallow-machined parts achieved only 68% and 8% of UTS and elongation of the deep-machined parts, respectively. This low performance occurred to be comparable to the as-built parts, which failed prematurely due to the high fraction surface voids and notches as well as the subsurface defects.

The nickel‐based superalloys Inconel alloy 600, Udimet alloy 720, and Inconel alloy 718 were produced by electron beam melting (EBM), casting, and directional solidification (DS). The distance between dendrites and the size of the precipitates indicated the difference in solidification rates between the three processes. In this study, the solidification rate was fastest with EBM, closely followed by casting, whereas it was much slower with DS. In the directional solidified materials the <100> direction was the fastest and thus, preferred growth direction. The EBM samples show a sharp (001)[100] texture in the building direction and in the two scanning directions of the electron beam. Macrosegregation was observed in some cast and directionally solidified samples, but not in the EBM samples. The melting temperatures are in good agreement with literature and the narrow melting interval of IN600 compare to UD720 and IN718 might reduce the risk of incipient melting during EBM processing. Porosity was observed in the EBM samples and the reasons are discussed. However, EBM seems to be a feasible process route to produce nickel‐based superalloys with well‐defined texture, no macrosegregation and a rapidly solidified microstructure.

In this paper, we use Oven Desorption followed by Karl Fischer Titration (KF), to measure moisture content in metal powder. In a PBF-LB Hastelloy X powder, from a newly opened container, we found 28.8 ppm (or µg/g). In a stored PBF-EB powder we found 13.7 ppm. In a stored HIP powder we found 6.7 ppm. This method heats a powder sample inside a hermetically closed vial, in an oven. At the same time an inert gas flow enters, flushes out the desorbed water and exits the vial, via a double hollow needle. The gas–water mixture that exits is directed to the Karl Fischer Titration, where the desorbed moisture is quantified. Included is also a comparison with thermogravimetric analysis (TGA) and a climate chamber moisturization experiment of a PBF-LB HX powder followed by KF analysis. After the moisturization and KF analysis, the same powder was characterized in terms of oxygen content.