[1] Deformation and hydration processes are intimately linked in the oceanic lithosphere, but the feedbacks between them are still poorly understood, especially in ultramafic rocks where serpentinization results in a decrease of rock density that implies a volume increase and/or mass transfer. Serpentinization is accompanied by abundant veining marked by different generations of vein-filling serpentines with a high variety of morphologies and textures that correspond to different mechanisms and conditions of formation. We use these veins to constrain the role of deformation and mass transfer processes during hydration of oceanic peridotites at slow-spreading ridges. We have selected a representative set of veins from ocean floor serpentinites of the Mid-Atlantic Ridge near Kane transform fault (23°N) and characterized these in detail for their microstructures and chemistry by coupling optical and electron microscopy (SEM, TEM) with electron microprobe analyses. Four main veining episodes (V1 to V4) accompany the serpentinization. The first episode, identified as vein generation V1, is interpreted as the tectonically controlled penetration of early seawater-dominated fluid within peridotites, enhancing thermal cracking and mesh texture initiation at 3-4 km up to 8 km depth and at T <300-350°C. The two following vein stages (V2 and V3) formed in a closed, diffusive system and accommodate volume expansion required to reach almost 50% serpentinization of the protolith. The cracks exploited by these veins were caused by the progressive unroofing at depths of 4 to 2 km along a detachment fault. Degree and rate of serpentinization seem to be controlled by the capacity of the system to create space and to drive the mass transfer needed for ongoing serpentinization, and this capacity is in turn linked to the exhumation rate and local tectonics. During this period, water consumed by hydration may prevent the establishment of convective hydrothermal cells. The onset of an open hydrothermal system in the shallow lithosphere (<2 km), where brittle fracturing and advective transfer dominate and enable the completion of serpentinization, is marked by the last vein generation (V4). These results show a complete history of alteration, with the crystallization of different types of serpentine recording different tectonic events, chemical conditions, and modes of hydrothermal alteration of the lithosphere.

No abstract

No abstract

[1] Two TCDP boreholes A and B were drilled in the northern part of the Chelungpu thrust fault where the Chi-Chi earthquake (21 September 1999, Mw 7.6) showed large displacement, low ground acceleration, and high slip velocity. In this paper, we describe the microstructures of the Chi-Chi Principal Slip Zone (PSZ) within black gouges localized at 1111 m depth in Hole A and at 1136 m depth in Hole B. In the FZA1111 the PSZ is a 2 cm-thick isotropic clay-rich gouge which contains aggregates formed by central clasts coated by clay cortex (clay-clast aggregates (CCAs)) and fragments of older gouges segregated in the top third of the PSZ. In FZB1136 the PSZ is 3 mm thick and is characterized by a foliated gouge displaying an alternation of clay-rich and clast-rich layers. The presence of CCAs, plucked underlying gouge fragments, gouge injections, and the occurrence of reverse grain size segregation of large clasts in the FZA1111 isotropic gouge suggest that the gouge was fluidized as a result of frictional heating and thermal pressurization. The foliated gouge in FZB1136 may be one locus of strain localization and related heat production. Small calcite veins present above the isotropic FZA1111 PSZ gouge and, characterized by an increasing strain with increasing distance away from the PSZ, are attributed to coseismic fluid escape from the pressurized gouge. The observed microstructures are interpreted in view of their seismic implications for the Chi-Chi earthquake in terms of slip weakening mechanisms by thermal pressurization, gouge fluidization, coseismic fluid distribution, and postseismic slip. Above the PSZ, several layers of compacted gouges containing deformed CCAs and gouge fragments correspond to several PSZ of past earthquakes similar to the Chi-Chi earthquake and display a fault-parallel cleavage resulting from a low strain rate pressure solution deformation mechanism that may be correlated to the interseismic periods.

No abstract

No abstract

No abstract

Active faults in the upper crust can either slide steadily by aseismic creep, or abruptly causing earthquakes. Creep relaxes the stress and prevents large earthquakes from occurring. Identifying the mechanisms controlling creep, and their evolution with time and depth, represents a major challenge for predicting the behavior of active faults. Based on microstructural studies of rock samples collected from the San Andreas Fault Observatory at Depth (California), we propose that pressure solution creep, a pervasive deformation mechanism, can account for aseismic creep. Experimental data on minerals such as quartz and calcite are used to demonstrate that such creep mechanism can accommodate the documented 20 mm/yr aseismic displacement rate of the San Andreas fault creeping zone. We show how the interaction between fracturing and sealing controls the pressure solution rate, and discuss how such a stress-driven mass transfer process is localized along some segments of the fault