Gold nanoparticles supported on different oxides (SiO 2 , CeO 2 and TiO 2 ) were prepared by the SMAD (solvated metal atom dispersion) and deposition-precipitation (DP) techniques. The physical and chemical characterization of the catalysts was performed by X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) and the catalytic activity was tested during the reaction of low temperature CO oxidation. The structural and surface analyses evidenced the presence of small gold crystallites (cluster size ∼2-5 nm) in all the SMAD-prepared samples and oxidized gold species in the case of the DP catalysts. A different surface distribution of ionic gold species was found on the different supports. By comparing the catalytic activities of the samples, the presence of Au +1 species seems to be the main requisite for the achievement of the highest CO conversion at the lowest temperature. The higher activity of Au/CeO 2 (DP) catalysts at T ≈ 250 K can be ascribed to a better stabilization of the AuO − species by the cerium oxide. Nanosized metallic gold particles exhibit a worse catalytic performance, both on 'reducible' and 'inert' supports, being significantly active only in the temperature range: 400-600 K.

Co 3 O 4 nanocrystals and Co 3 O 4 -MO x binary oxides for CO, CH 4 and VOC oxidation at low temperatures: a review

Gold catalysts supported on cerium oxide were prepared by solvated metal atom dispersion (SMAD), by deposition-precipitation (DP), and by coprecipitation (CP) methods and were characterized by X-ray diffraction (XRD), temperature programmed reduction (TPR), and X-ray photoelectron spectroscopy (XPS). The catalytic activity was tested in the CO oxidation reaction. The structural and surface analyses evidenced the presence of a modified ceria phase in the case of the DP sample and the presence of pure ceria and gold metal crystallites in the case of the SMAD and CP samples. The DP sample, after a mild treatment in air at 393 K, exhibited only ionic gold, and it was very active below 273 K. By comparing the activities of the different catalysts, it is suggested that the presence of small gold particles, as obtained by the SMAD technique, is not the main requisite for the achievement of the highest CO conversion. The strong interaction between ionic gold and ceria, by enhancing the ceria surface oxygen reducibility, may determine the particularly high activity.

Polycrystalline ZnO/TiO2 solids have been prepared with four different methods using home prepared TiO2 (anatase) or TiO2 (rutile) as supports and Zn(NO3)2·6H2O or Zn(CH3COO)2·2H2O as precursors for ZnO. The bulk and surface properties of the samples were investigated by means of TG-DTA, XRD, TEM, SEM-EDAX, XPS, BET surface area determination, and porosity measurements. XRD and TEM results indicate that no significant defect structures exist in any of the samples. The ZnO crystallinity and its enrichment on the surface of TiO2 particles were dependent on the preparation method. The surface areas generally decrease by increasing the amount of ZnO except when ZnO from Zn(CH3COO)2·2H2O was supported on TiO2 (rutile). The samples prepared from Zn(CH3COO)2·2H2O were more porous than those prepared from Zn(NO3)2·6H2O. This was confirmed by BET surface area determinations and SEM observations. XPS spectra indicate that the atomic ratio between OH- and O2- on the particles surface is similar for samples with the same ZnO content independent of the precursor used for the samples' preparation. Moreover a much higher segregation of ZnO was found for samples obtained by using the acetate precursor.

No abstract

Electron spin resonance spectroscopy (ESR), Fourier transform infrared spectroscopy (FTIR), and monitoring of pyridine (py) and boric acid trimethyl ester (BATE) adsorption for determining surface acidity and basicity, respectively, were used to carry out further characterization of mixed ZnO/TiO 2 polycrystalline solids prepared by different methods. Moreover, the powders were tested in a batch photoreactor for a probe reaction, i.e., 4-nitrophenol photodegradation in aqueous medium. ESR results indicated the presence of signals attributable to Zn + species in ZnO/TiO 2 (anatase) solids, while in ZnO/TiO 2 (rutile) samples the presence of zinc induced only the formation of signals probably due to Ti 3+ centers. FT-IR spectra showed no significant differences of the surface hydroxylation degree of the various photocatalysts, whereas the surface acidic properties generally decrease by increasing the amount of ZnO. Coupling of ZnO and TiO 2 semiconducting powders was not so beneficial, as expected on the basis of the intrinsic electronic properties, to enhance the photoreactivity for the studied reaction, although some of the powders showed photoactivities slightly higher than those of bare TiO 2 and ZnO. Nevertheless, some of the samples (the mixed particles ZnO/TiO 2 (rutile)) appear promising from an application point of view because no filtration was needed after the occurrence of the photoreactivity tests to separate them from the solution because they decanted easily. The mineralization of 4-nitrophenol was checked by determining the total organic carbon (TOC) and a complete photooxidation occurred in few hours in the presence of some of the samples.

No abstract

No abstract