The sound absorption coefficient is a commonly used parameter to characterize the acoustic properties of materials. The fire performance of construction products has to be evaluated on the basis of their reaction to fire performance. The evaluation of the reaction to fire performance for the flammable construction materials which are in Class E reaction to fire is based on the ignitability test and the thermal test using the radiant heat source. For this study, nine types of STERED® products, which were made from the recycled automotive technical textiles, were chosen in order to evaluate their ability for sound absorption and the reaction to fire. The fire performance was evaluated on the basis of the relative mass loss in the radiant heat source test; the ignitability in accordance with ISO 11925-2, the possible appearance of flame, duration of flame, and the glowing during the single flame source test. The sound absorption of nine products was rated on the basis of the sound absorption coefficient and the noise reduction coefficient. The measurement was performed using the transfer function method in accordance with ISO 10534-2. From the nine tested types of STERED® products, the product Senizol AT XX2 TL 60 had the lowest mass loss at thermal loads up to 700 °C and it fulfilled the conditions for Class E reaction to fire. This product had the highest noise reduction coefficient of 0.81 and a high absorption coefficient for frequencies ranging between 500 Hz and 2000 Hz. The STERED® product Senizol AT XX2 TL 60, as well as Senizol AT 22 TL 50, Senizol AT 40 TL 25, Senizol AT XX4 TL 50 and Senizol AT XX4 TL 10 with a sound absorption coefficient α of between 0.80 to 0.95 and corresponding NRCs from 0.66 to 0.81, these STERED® products can be classified according to ISO 11654 into the sound absorption classes A and B.

No abstract

The paper deals with comparing the measurement of noise from the railroads in the residential zone of the town of Zvolen with the results calculated using the prediction methods “Schall 03“ (Deutsche Bundesbahn, 1990) and “Methodical instructions for the calculation of sound pressure level from transport” (MPVHD). The first is used in the Slovakia and second in the Czech Republic. The measurement results and the results obtained from the prediction methods for both measurement locations were evaluated graphically and statistically. The evaluation of the conformity of the measurement with the prediction showed that the results obtained using the method “Schall 03” are in better agreement with the measurement.

Effects of biological modification of Norway spruce wood with the wood-staining fungus Sydowia polyspora were evaluated relative to select physical and acoustical characteristics (PACHs), including the density (ρ), dynamic modulus of elasticity along the wood grain (EL), specific modulus (Esp), speed of sound along the wood grain (cL), resonant frequency (fr), acoustic constant (A), logarithmic decrement (ϑ), loss coefficient (η), acoustic conversion efficiency (ACE), sound quality factor (Q), and sound timbre. Incubation of the Norway spruce samples in S. polyspora lasted 12 w, 20 w, and 24 w. The results showed that the incubation time of spruce wood in S. polyspora did not have a statistically significant impact on most of the PACHs (ρ, EL, cL, fr, and A). However, biological modification of the spruce wood with S. polyspora had significant effects on the ϑ, η, and ACE. Treatment of the spruce wood with S. polyspora also changed the sound timbre, but the effects varied for each frequency.

This article presents a proposal of thermal modification of Norway spruce and sycamore maple for special wood products, mainly for musical instruments. Selected physical and acoustical characteristics (PACHs), including the density (ρ), dynamic modulus of elasticity along the wood grain (EL), specific modulus (Esp), speed of sound along the wood grain (cL), resonant frequency (fr) and acoustic constant (A), logarithmic decrement (ϑ), loss coefficient (η), acoustic conversion efficiency (ACE), sound quality factor (Q), and the timbre of sound, were evaluated. These two wood species were chosen regarding their use in the production or repair of musical instruments. For the thermal modification, a similar process to the ThermoWood process was chosen. Thermal modification was performed at the temperatures 135 °C, 160 °C and 185 °C. The resonant dynamic method was used to obtain the PACHs. Fast Fourier transform (FFT) was used to analyze the sound produced. The changes in the observed wood properties depended on the treatment temperature. Based on our results of all properties, the different temperature modified wood could find uses in the making of musical instruments or where the specific values of these wood characteristics are required. The mild thermal modification resulted in a decrease in mass, density, and increased speed of sound and dynamic modulus of elasticity at all temperatures of modification. The thermally modified wood showed higher sound radiation and lower loss coefficients than unmodified wood. The modification also influenced the timbre of sound of both wood species.