Electrocoagulation is one of methods used to treat wastewater in the coal stockpile without using coagulants. Characteristics of wastewater observed are heavy metals (Fe and Mn) and pH. The decrease in the heavy metals content and the increase in the pH of this wastewater treatment process will then be proposed in the adsorption kinetics model. The influence of variations in currents and processing time were observed. The time variation of the adsorption process were 60 to 120 minutes with current variations from 1.3 to 3.0 Ampere at a fixed 12 voltages. The results obtained that the Fe content could be decreased to 0.03 ppm at 90 minutes while the content of Mn was decreased to 0.01 ppm at the same time. The increase in pH (7.11) was achieved when applying 2.5 A current at 90 minutes process time. The results obtained from the electrocoagulation method was then proposed in the model of the Langmuir isotherm adsorption kinetics and Freundlich isotherm.
Kebutuhan industri akan air bersih sangatlah tinggi sehingga diperlukan proses pengolahan. PLTG Borang merupakan salah satu industri yang mendapatkan air bersih dengan melakukan pengolahan pada unit Water Treatment Plant. Unit WTP di PLTG Borang mengalami permasalahan di beberapa alat seperti misalnya pada prasedimentasi. alat ini berfungsi sebagai tempat proses pengendapan partikel diskrit seperti pasir, lempung, dan zat-zat padat lainnya yang bisa mengendap secara gravitasi. Data-data yang dijadikan sumber yaitu data variabel proses dan hasil kualitas mutu air setelah pengolahan pada prasedimentasi. Data variabel proses yang diperlukan yaitu laju alir, waktu pengendapan. Sedangkan kriteria kualitas yang diperlukan yaitu turbiditas, TDS, dan TSS. Variabel proses divariasikan yaitu; laju alir 1, 2, 3, 4 dan 5 L/detik; waktu pengendapan 50, 75 dan 100. Analisis data yang dilakukan yaitu dengan menginterpretasikan data hasil pengamatan dan menyajikannya dalam bentuk grafik kemudian akan diperoleh kesimpulan. Variabel proses yang optimal adalah laju alir 1 L/detik, dan waktu pengendapan 100 menit. Hasil kualitas air setelah pengolahan di prasedimentasi yaitu Turbiditas 370 NTU; TDS 605 ppm; dan TSS 402 ppm.
Peningkatan produksi pulp dengan kebutuhan bahan baku tidak seimbang, dimana proses pembentukan kayu membutuhkan waktu yang lama, namun produksi pulp terus meningkat. Oleh karena itu, dibutuhkan bahan baku alternatif selain kayu yaitu Tandan kosong kelapa sawit dan pelepah pisang. Proses pemasakan pulp sangat menentukan berjalannya proses dan juga berpengaruh terhadap penentuan kualitas pulp yang dihasilkan, sehingga dilakukan perancangan sistem pengendalian temperatur on/off otomatis sebagai pelengkap pada alat digester pembuatan pulp tipe batch yang mudah dioperasikan, efektif dan aman. Metode penelitian diawali dengan dengan merancang sistem pengendalian temperatur yang meliputi kontroler, transduser, termokopel, dan heater. Kemudian diuji kinerja pengendalian tersebut dengan pembuatan pulp. Parameter penelitian ini ialah variasi suhu dan temperatur di dalam digester dengan waktu pengamatan setiap 30 detik pada kondisi temperatur set point 100oC, 105oC, 110oC, 115oC dan 120oC. Hasil pengujian menunjukkan bahwa dengan menggunakan mode pengendali on/off otomatis memiliki error pengukuran 0,875oC, histerisis control lag rata-rata 96 detik dan periode osilasi rata-rata 9,7 menit. Selain itu, penerapan sistem pengendali temperatur melalui pembuatan pulp menghasilkan rendeman pulp sebesar 52,56% dan kadar selulosa 55,74%.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.