Yerba mate (YM) is widely consumed in Latin American countries, and its residues can be used as bio‐resources such as reinforced in epoxy composites. The present work aims to produce epoxy resin composites and evaluate the influence of post‐consumed YM as reinforcement. The concentrations of YM used were 5, 10, and 20% (wt/wt). Chemical, thermal, morphological, and dynamic mechanical behaviors were explored. The YM incorporation did not influence chemically on the epoxy structure and a pull‐out phenomenon was observed as YM content increased. The YM at lower concentrations (5 and 10%) led to higher values of activation energies calculated from model‐free isoconversional methods. On the other hand, the composite e/YM 20 wt% improved all dynamic‐mechanical properties. YM proved to be a suitable and cheap reinforcement for epoxy resin.
Degradation kinetics is an important tool in order to understand and improve energy conversion and the final application of a material. Cellulose cryogels (CC) are a new class of materials that can be reinforced by several types of particle, including biochar. Apart from it, degradation kinetics and lifetime prediction of biomass cellulose cryogels reinforced by cellulose pyrolysis waste (BC) has been investigated using TG techniques and iso-conversional model free methods. Additionally, the same study was applied to cellulose cryogels reinforced by graphene nanoplatelets (NPG) to compare the behavior of a filler from waste (BC) and a noble filler (NPG). Furthermore, the influence of the addition of the fillers into the cellulose biomass were evaluated in terms of thermal stability and crystallinity. BC and GNP led to higher values of activation energies ( a E ) calculated from modelfree isoconversional methods and all samples degraded in two-steps. Finally, lifetime prediction was successfully applied and the CC cryogel became more stable over time, maintaining almost 80% of the mass for 1 year exposed at 180 °C. The results of this study shown that only cellulose biomass cryogels are more suitable to produce thermal insulators due to it higher thermal stability.
Resumo Células solares com emissor e face posterior passivada (PERC, passivated emitter and rear cell) vêm dominando o mercado fotovoltaico em razão de seu processo de fabricação ser compatível com as linhas industriais que vinham sendo utilizadas e pela produção de dispositivos de alta eficiência. Atualmente o silício tipo p é o mais utilizado pela indústria de células solares, mas o silício tipo n deve ganhar mercado nos próximos anos juntamente com o emprego de lâminas de espessura reduzida. O objetivo deste trabalho é apresentar uma revisão sistemática dos principais estudos na área de células solares base n, sendo elas do tipo PERC, PERT (passivated emitter-rear totally diffused) e TOPCon (tunnel oxide passivated contact), com ênfase para a abordagem de contatos seletivos, emissores seletivos e nos processos utilizados, bem como na análise de células solares de espessura reduzida em relação ao padrão da indústria atual.
As células solares bifaciais fabricadas em lâminas de silício cristalino tipo n apresentam potencial de obtenção de maior eficiência e bifacialidade próxima a um. Com este foco, o objetivo deste artigo é analisar a influência do método de formação do emissor produzido na mesma etapa térmica que o campo retrodifusor nos parâmetros elétricos de células solares bifaciais base n com estrutura PERT e passivação das superfícies com SiO2. Foi utilizado o método de spin-on e a difusão do boro foi realizada em forno convencional, seguida da difusão do fósforo com POCl3. Variou-se a temperatura de difusão de boro e analisou-se a resistência de folha do emissor e do campo retrodifusor dopado com fósforo bem como a influência nos parâmetros elétricos das células solares bifaciais. Verificou-se que a resistência de folha do emissor de boro diminuiu de (116 ± 6) Ω/sq para (64 ± 2) Ω/sq com o aumento da temperatura de difusão de boro de 940 °C a 980 °C. Porém, a resistência de folha do campo retrodifusor de fósforo aumentou, indicando que a difusão de boro afeta a região dopada com fósforo. As maiores eficiências, de 15,3% e 15,5 % com irradiância no emissor e campo retrodifusor, respectivamente, foi alcançada com a temperatura de difusão de 960 °C. Neste dispositivo, a bifacialidade foi de 0,987. Constatou-se que a tensão de circuito aberto foi maior com irradiância no emissor, independente da temperatura de processamento. Também se concluiu que a tensão de circuito aberto e o fator de forma cresceram até a temperatura de processamento de 960 °C, independente do modo de iluminação. Porém, a densidade de corrente de curto-circuito com irradiância no emissor tendeu a diminuir, devido ao aumento da recombinação dos portadores de carga minoritários. O fator de forma foi o parâmetro elétrico que mais influenciou na eficiência.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.