Abstract. This paper deals with a cylindrical steel-concrete load-bearing unit. The feature of the unit is a steel mesh casing that is made from the expanded metal mesh. The optimal parameters of the suggested footing are determined taking into account anisotropy, i. e. different strength and rigidity in different directions that coincide and do not coincide with the direction of reinforcement. The optimal cell angle, when a casing deformation brings about maximum compression of a concrete core, is determined. Details for theoretical calculation of the bearing capacity of a cylindrical steel-concrete load-bearing unit are provided taking into consideration a complex threedimensional structure of the suggested mesh casing. The validity of the calculations is confirmed by comparison them with the results of the Lira software package. The results of the calculations are provided in the form of the table showing the dependence of the adduced thickness of the plate on the longitudinal movement of the strip of the steel mesh casing. The dependencies to determine the adduced thickness of the mesh casing using the graphical method are provided for all the existing types of the mesh using concrete wedges or excluding them.
1 Харьковский национальный технический университет сельского хозяйства имени Петра Василенко 2 Харьковский национальный автомобильно-дорожный университет Аннотация. Предлагаются алгоритмы подбора размеров поперечных сечений бетона и стального листа с предельными напряжениями в бетоне и стальном листе, а также с предельными коэффициентами армирования. Предельным является коэффициент армирования, при котором максимальные напряжения в бетоне и стальном листе будут предельными. Ключевые слова: сталебетонная балка, бетон, стальной лист, предельные напряжения, предельный коэффициент армирования, приведенное сечение. Введение Сталебетонные конструкции в целом и сталебетонные балки в частности получают все большее распространение в строительстве. Эти конструкции, по сравнению с традиционными железобетонными, являются более экономичными. Таким образом, задача их оптимизации является актуальной. Анализ публикаций Вопросами расчета сталебетонных балок занимались многие авторы [1]-[5] и др. Во многих статьях уделяется внимание исследованию работы гибких анкеров [2], [3], формам разрушения сталебетонных балок [4], определению их несущей способности при разрушении по нормальному сечению и по контакту [5]. В [6] предложен расчет сталебетонных элементов с использованием теории Яшина.
Цель и постановка задачиЦелью исследования является оптимизация расчета сталебетонных балок по несущей способности.Для достижения поставленной цели необходимо разработать методику расчета сталебетонных балок с учетом работы бетона в растянутой зоне.
While designing an ore-thermal furnace it is necessary to minimize and balance its secondary current contact jaw electrical parameters. The study deals with the method of calculating pure resistance and inductance of ore-thermal furnace electrode holder tubes. It is significant because the tubes have complicated wires configuration and their resistance is noticeable in current contact jaw total impedance because of the same half-phase currents flow in tube bundles and absence of magnetic flux compensation. Real bent wires are suggested to be approximated by broken lines. After that both existing and proposed by the authors formulas can be used for calculating inductance and mutual inductance of two straight-line wires arbitrary placed in space. Current distribution non-uniformity along separate tubes is taken into account in an iterative algorithm. Currents in wires are assumed to be equal at the first iteration. Then they are corrected at following steps of the iteration algorithm with respect to wires resistances calculation results. Skin effect and closure effect between wires segments are taken into account when pure resistance is calculated. The proposed method has been applied in the development of the software for calculating ore-thermal furnace secondary current-contact jaw electrical parameters. The method has been approbated in the design of the 60 MVA ore-thermal furnace made by ZAO “Electroterm”, Novosibirsk, Russia. The results obtained have been tested with numeric 3D models created in ANSYS environment. Inductance calculation error is 10%, pure resistance error is 25%.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.