A polycrystalline Cu2ZnSnS4 thin film was deposited on fused quartz by co-evaporation. The selected thickness was ~100 nm to avoid artifacts in its optical properties caused by thicker as-grown films. The composition and phase of the film were checked with x-ray fluorescence, Raman shift spectroscopy, scanning transmission electron microscopy, and energy dispersive x-ray spectroscopy. An improved spectroscopic ellipsometry methodology with two-side measurement geometries was applied to extract the complex dielectric function ε = ε1 + iε2 of the Cu2ZnSnS4 thin film between 0.73 and 6.5 eV. Five critical points were observed, at 1.32 (fundamental band gap), 2.92, 3.92, 4.96, and 5.62 eV, respectively. The ε spectra are in reasonable agreement with those from theoretical calculations.

Silicon has been investigated in recent years as an alloying anode material to enhance gravimetric energy density in lithium-ion batteries. While recent developments have suggested that silicon oxides exhibit improved cycling stability over pure Si, the origin of the improved cycling performance is still poorly understood. The initial solid electrolyte interphase (SEI) formation mechanisms on Si wafers with both native oxide and chemically etched thermal oxide coatings are investigated structurally, chemically, and morphologically in the nanoscale. After one electrochemical cycle, microscopy reveals that SEI formed on native SiO x features the typical SEI bilayer structure with a carbon-rich outer SEI layer and an inorganic-rich inner SEI layer. In contrast, the SEI formed on chemically etched thermal oxide shows an inversion in the structure. This work observes distinct initial SEI formation mechanisms on the HF-etched SiO 2 surface, which may be partially responsible for improved cycle life observed in SiO x -based anode materials.

CuGa3Se5 is a promising candidate material with wide band gap for top cells in tandem photovoltaic and photoelectrochemical (PEC) devices. However, traditional CdS contact layers used with other chalcopyrite absorbers are not suitable for CuGa3Se5 due to the higher position of its conduction band (CB) minimum. Mg x Zn1− x O (MZO) is a transparent oxide with adjustable band gap and CB position as a function of magnesium composition, but its direct application is hindered by CuGa3Se5 surface oxidation. Here, MZO is investigated as a contact (n-type ‘buffer’ or ‘window’) material to CuGa3Se5 absorbers pretreated in Cd2+ solution, and an onset potential close to 1 V vs reversible hydrogen electrode in 10 mM hexaammineruthenium (III) chloride electrolyte is demonstrated. The Cd2+ surface treatment changes the chemical composition and electronic structure of the CuGa3Se5 surface, as demonstrated by photoelectron spectroscopy measurements. The performance of CuGa3Se5 absorber with Cd2+ treated surface in the solid-state test structure depends on the Zn/Mg ratio in the MZO layer. The measured open circuit voltage of 925 mV is promising for tandem PEC water splitting with CuGa3Se5/MZO top cells.

The use of nanopatterned {111}-faceted v-grooves has recently shown promise for growing high-quality III−V material on Si. Here, we study the effect of reactor conditions and surface pretreatments on the nucleation of GaP on v-grooved Si in a high-temperature regime, which offers the promise of a defect-free GaP/Si interface favorable for Si passivation and dislocation glide in the GaP. X-ray photoelectron spectroscopy was used to understand the Si surface chemistry prior to nucleation, and transmission electron microscopy was used to probe material quality of the nuclei. Temperature and V/III ratio were found to control the facet selectivity of nucleation. We demonstrate a condition of high temperature and high V−III ratio that leads to uniform nucleation at the bottom of the trenches, with initial material free of nucleation-related interfacial defects. This optimized condition was then shown to coalesce into a thin film after additional growth.

As thin-film cadmium telluride (CdTe) solar cells gain prominence, one particular challenge is optimizing contacts and their interfaces to transfer charge without losses in efficiency. Back contact recombination is still significant and will prevent CdTe solar technology from reaching its full potential in device efficiency, and transparent back contacts have not been developed for bifacial solar technology or multijunction solar cells. To address these challenges, this study investigates sputtered Cu x Zn 1−x S as a p-type semi-transparent back contact material to thin-film polycrystalline CdTe solar cells at Cu concentrations x = 0.30, 0.45, and 0.60. This material is selected for its high hole conductivity (160−2120 S cm −1 ), wide optical band gap (2.25−2.75 eV), and variable ionization potential (approximately 6−7 eV) that can be aligned to that of CdTe. We report that without device optimization, CdTe solar cells with these Cu x Zn 1−x S back contacts perform as well as control cells with standard ZnTe:Cu back contacts. We observe no reduction in external quantum efficiency, low contact barrier heights of approximately 0.3 eV, and carrier lifetimes on par with those of baseline CdTe. These cells are relatively stable over one year in air, with V OC and efficiency of the x = 0.30 cell decreasing by only 1 and 3%, respectively. Using scanning electron microscopy and scanning transmission electron microscopy to investigate the Cu x Zn 1−x S/CdTe interface, we demonstrate that the Cu x Zn 1−x S layer segregates into a bilayer of Cu-Te-S and Zn-Cd-S, and thermodynamic reaction calculations support these findings. Despite its bilayer formation, the back contact still functions well. This investigation explains some of the physical mechanisms governing the device stack, inspires future work to understand interfacial chemistry and charge transfer, and elicits optimization to achieve higher-efficiency CdTe cells.