Cement-retained implant-supported prosthetics are gaining popularity compared to the alternative screw-retained type, a rise that serves to highlight the importance of retrievability. The aim of the present investigation is to determine the influence of luting agent, abutment height and taper angle on the retrievability of abutment–coping cementations. Abutments with different heights and tapers were screwed onto an implant and their cobalt-chrome copings were cemented on the abutments using three different luting agents. The removals were performed by means of Coronaflex®. The number of impulses and the forces were recorded and analyzed with a Kruskal–Wallis test. Harvard cement needed the highest number of impulses for retrieval, followed by Telio CS and Temp Bond. However, abutment height and taper showed a greater influence on the cap’s retrievability (p < 0.05). Long and tapered abutments provided the highest percentage of good retrievability. The influence of the luting agent and the abutment geometry on the cap’s retrieval performed by Coronaflex® reflects data from literature about the influence of the same factor on the maximum force reached during uniaxial tensile tests. The impulse force was slightly affected by the same factors.

Implant fixed dental prostheses are widely used for the treatment of edentulism, often preferred over the screw-retained ones. However, one of the main features of an implant-supported prosthesis is retrievability, which could be necessary in the case of implant complications. In this study, the retrievability of implant-fixed dental prostheses was investigated considering two of the main factors dental practitioners have to deal with: the abutments geometry and the luting agent. Impulsive forces were applied to dental bridge models to simulate crowns’ retrievability in clinical conditions. The number of impulses and the impulsive force delivered during each test were recorded and used as retrievability indexes. One-hundred-and-five tests were conducted on 21 combinations of bridges and luting agents, and a Kruskal-Wallis test was performed on the results. The abutment geometry significantly influenced the number of impulses needed for retrieval (p < 0.05), and a cement-dependent trend was observed as well. On the other hand, the forces measured during tests showed no clear correlation with bridge retrievability. The best retrievability was obtained with long, slightly tapered abutments and a temporary luting agent.

The study of the biomechanics of the human spine is not yet developed extensively. Recent developments in this field have heightened the need for observing the spine from a comprehensive perspective to understand the complex biomechanical patterns, which underlie the kinematic and dynamic responses of this multiple-joint column. Within this frame of exigence, a joint study embracing experimental tests and multibody modelling was designed. This study provides novel insights to the segmental contribution profiles in flexion and extension, analysing different forms of sagittal-plane angles. Moreover, the validation of the multibody model contributes to defining the key aspects for a consistent spine modelling as well as it introduces the basis for simulating pathological conditions and post-orthopaedic surgical outcomes.

When a new material for the realization of an implantable device in the bone is being studied, in addition to its chemical-physical-mechanical characterization, tests regarding osteointegration are performed. Usually, researchers evaluate the ability of biomaterials to bind to the bone under load-bearing conditions, through animal experiments in the phase of a preclinical study, provided the respective authorization by the ethics committee. In more detail, plugs made of the material under investigation are prepared and implanted into a weight-bearing portion of the skeleton of animals (typically into the knee joint of goats, pigs, rabbits or dogs); after a pre-set time, the animal is sacrificed, the bone element is extracted, it is tested mechanically -generally by means of a pull-out test -and finally it is examined histologically. Mechanical tests often require demanding specimen preparation, which could bias results. In the scope of a research regarding the interface behaviour of a ceramic plug (two different ceramic plugs) compared to a titanium one, the authors have suggested a novel testing technique which allows to perform 'push-in' tests, instead of the more common pull-out tests. This methodology has been followed here to compare titanium versus ceramic plugs at different times from implant (0, 3 months, 1 year) into goat knees. As a result, the study reports the shear resistance of bone-plug interfaces. The statistical analysis of the data allowed us to establish that titanium plugs systematically exhibit a higher resistance (p<0.10); this resistance undergoes a significant increment as time passes (p<0.07) due to progressive osteointegration.

The split crest is an established surgical technique for horizontal bone augmentation. It allows to place implants of adequate diameter in sites where the bone would be too thin for the implantation. In this study, two split crest techniques (using threaded bone expanders or ultrasonic bone surgery) were performed ex vivo on bovine ribs, and dental implants were then inserted in the so prepared implantation sites. Digital image correlation was used to measure the bone external surface displacement throughout the surgical procedures. Both techniques provided an adequate bone volume for implant insertion, and no significant differences were highlighted regarding the displacement. However, bone accidental fracture only occurred during split crest with threaded bone expanders, suggesting differences in the internal strain distribution induced by the two techniques.

In silico modeling of osteosynthesis medical devices allows the reduction of the time required for experimental tests and the introduction of “simulation-driven design”. Using a wise combination of these techniques and analytical calculations, it is possible to relate the experimental results, which are mandatory for regulatory purposes, to the plate physiological application and prevent the occurrence of complications in the early stages after the orthopedic device implantation on humans and animals.

The use of new prosthetic materials makes it necessary to establish adequate hygienic protocols. It was decided to make prosthetic crowns from four different materials: composite, lithium disilicate, metal ceramic, and zirconium, and to evaluate the effects on the surfaces of four different instruments through SEM and roughness analysis: manual steel curette, manual titanium curette, ultrasonic steel insert, and ultrasonic peek insert. Forty crowns were made, ten of each type of material. For each material, five crowns were manually instrumented with steel inserts (curette 11-12, PDT, Missoula, MT, USA) and titanium (Wingrove 3-4, PDT, Missoula, MT, USA) on the lingual and buccal surfaces, respectively, and the other five crowns were instrumented with an ultrasonic peek insert (ICS-IC1, Mectron, Carasco, Italy) on the buccal surface and steel (PS, EMS, Nyon, Switzerland) on the lingual surface. At this point, surface roughness analysis was carried out. The data were analyzed with a Kolmogorov–Smirnov test. Therefore, it was decided to conduct two analyses with a Kruskal–Wallis test and Bonferroni post hoc test. Then, the instrumented crowns were analyzed by SEM. The analysis of the data shows that the highest average roughness was within the composite group, while the best material appeared to be disilicate. Significant differences existed between the groups, between the materials, and between the different instruments (p-value < 0.05). In the qualitative analysis carried out by SEM, the classic steel insert eliminated the residues of golden finishing. The peek insert created alterations on all tested surfaces. The steel curette did not create particular problems, with the exception of zirconium, where it was possible to observe some scratch lines. Instrumentation with the titanium curette created deeper incisions than the steel curette in the composite and disilicate. The best results came from the ultrasonic steel insert, while the best material appeared to be disilicate.

Micromechanical characterization by nanoindentation of PDMS substrates for cardiac mechanobiology studies.