У статті розглядаються області несучих здатностей для поперечних перерізів тонкостінних стержневих елементів конструкцій із холодногнутих профілів. Звертається увага на важливу властивість області несучої здатності – її випуклість. У статті представлений випадок, коли внутрішні зусилля зі значеннями, меншими за розрахункові, можуть бути більш несприятливими для невипуклої області несучої здатності стержневих елементів із холодногнутих профілів. Представлено алгоритм автоматизованої побудови областей несучої здатності для перерізів стержневих елементів конструкцій та його програмну реалізацію в обчислювальному комплексі SCAD Office. Побудова області несучої здатності поперечного перерізу разом із випуклою оболонкою заданих комбінацій внутрішніх зусиль є гнучким інструментом для аналізу умов навантажень. Виконані дослідження області несучої здатності для перерізів стержневих конструкцій із холодногнутих профілів слугують засобом критичного аналізу вимог норм проектування для досліджуваного класу конструкцій. Засвідчена невипуклість та стрибкоподібна зміна межі області несучої здатності, що обумовлена не- узгодженостями окремих положень нормативного документу [1]. Зокрема, такий характер області спостерігається при переході від однієї розрахункової ситуації (закритична стадія роботи елемента конструкції після досягнення явища втрати місцевої стійкості) до іншої (робота в межах пружніх деформацій сталі).
The article addresses one of the main issues that arise in the planned development of a new version of domestic standards, which is aimed at closer convergence with the European normative document EN 1990 in terms of calculation methods. If these methods are not fully accepted, then at least the principled positions are agreed, if possible preserving the domestic tradition An overview of the approaches of European standards EN 1990 to the compilation of design combinations of effects on building structures is given. The information on the method of choosing the calculated combination of influences of different groups of limit states taking into account different types of representative values of variable influences is generalized. Discrepancies with the methods of normative documents in force on the territory of Ukraine (DBN) on the calculation of building structures are indicated. Attention is drawn to the variability of Eurocode rules for the construction of settlement connections in relation to the situations under consideration, such variability is absent in the DBN. A compromise approach is proposed, which combines the principles of EN 1990 with the accumulated domestic experience and allows to significantly reduce the growth of design loads. The examples show that the increase in design effort causes significantly less increase in the cost of building materials.
Аннотация: Рассматривается вопрос о различиях в возможной реакции конструкции на неожиданное возмущение с учетом того, что предельное состояние конструкции является редким явлением и большую часть времени конструкция весьма далека от этого состояния. Предлагается особая мера указанного ка-чества конструкции, называемая мобилизованностью.Ключевые слова: случайная нагрузка, выброс за расчетный уровень, надежность MOBILIZATION AS A CHARACTERISTIC OF RELIABILITY OF STRUCTURESAnatolii V. Perelmuter SCAD Soft Ltd., Kiev, UKRAINE Abstract:The problem of the differences in the possible reaction of a structure to an unexpected perturbation is considered, taking into account the fact that the limiting state of a structure is a rare phenomenon and most of the time the design is very far from this state. A special measure of the specified quality of the structure is proposed, called mobilization.
This paper describes the approach implemented in SCAD for the analysis of behavior of fragments of thin-walled reinforced concrete structures taking into account the elastic-plastic behavior of both concrete and reinforcement.
This paper focuses on the regulation of forces in a statically indeterminate system under the action of many loads. This regulation is realized by prestressing. The paper compares two proposed methods for selecting rational values of the prestressing parameters: maximizing the minimum bearing capacity margin for the elements of the system (1) and equalizing the margins for all elements (2). An illustrative example is provided.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.