The film morphology and device performance of planar heterojunction solar cells based on the molecular donor material α-sexithiophene (6T) are investigated. Planar heterojunctions of 6T with two different acceptor molecules, the C 60 fullerene and diindenoperylene (DIP), have been prepared. The growth temperature of the 6T bottom layer has been varied between room temperature and 100 °C for each acceptor. By means of X-ray diffraction and X-ray absorption, we show that the crystallinity and the molecular orientation of 6T is influenced by the preparation conditions and that the 6T film templates the growth of the subsequent acceptor layer. These structural changes are accompanied by changes in the characteristic parameters of the corresponding photovoltaic cells. This is most prominently observed as a shift of the open circuit voltage (V oc ): In the case of 6T/C 60 heterojunctions, V oc decreases from 0.4 to 0.3 V, approximately, if the growth temperature of 6T is increased from room temperature to 100 °C. By contrast, V oc increases from about 1.2 V to almost 1.4 V in the case of 6T/DIP solar cells under the same conditions. We attribute these changes upon substrate heating to increased recombination in the C 60 case while an orientation dependent intermolecular coupling seems to change the origin of the photovoltaic gap in the DIP case.
The thermal behaviour of an organic photovoltaic (OPV) binary system comprised of a liquidcrystalline fluorene-based polymer and a fullerene derivative is investigated. We employ variabletemperature ellipsometry complemented by photo-and electroluminescence spectroscopy as well as optical microscopy and scanning force nanoscopy to explore phase transitions of blend thin films. The high glass transition temperature correlates with the good thermal stability of solar cells based on these materials. Furthermore, we observe partial miscibility of the donor and acceptor together with the tendency of excess fullerene derivative to segregate into exceedingly large domains. Thus, for charge generation less adequate bulk-heterojunction nanostructures are poised to develop if this mixture is exposed to more elevated temperatures. Gratifyingly, the solubility of the fullerene derivative in the polymer phase is found to decrease if a higher molecular-weight polymer fraction is employed, which offers routes towards improving the photovoltaic performance of non-crystalline OPV blends.
We present a comprehensive investigation of the charge-transfer (CT) effect in weakly interacting organic semiconductor mixtures. The donor-acceptor pair diindenoperylene (DIP) and N,N'-bis(2-ethylhexyl)-1,7-dicyanoperylene-3,4/9,10-bis(dicarboxyimide) (PDIR-CN) has been chosen as a model system. A wide range of experimental methods was used in order to characterize the structural, optical, electronic, and device properties of the intermolecular interactions. By detailed analysis, we demonstrate that the partial CT in this weakly interacting mixture does not have a strong effect on the ground state and does not generate a hybrid orbital. We also find a strong CT transition in light absorption as well as in photo- and electroluminescence. By using different layer sequences and compositions, we are able to distinguish electronic coupling in-plane vs out-of-plane and, thus, characterize the anisotropy of the CT state. Finally, we discuss the impact of CT exciton generation on charge-carrier transport and on the efficiency of photovoltaic devices.
Achieving control over the nanomorphology of blend films of the fullerene derivative [6,6]-phenyl C61-butyric acid methyl ester, PCBM, with light-absorbing conjugated polymers is an important challenge in the development of efficient solutionprocessed photovoltaics. Here, three new polyfluorene copolymers are presented, tailored for enhanced miscibility with the fullerene through the introduction of polymer segments with modified side chains, which enhance the polymer's polar character. The composition of the spincoated polymer:PCBM films is analyzed with dynamic secondary ion mass spectrometry (dSIMS). The dSIMS depth profiles demonstrate compositional variations perpendicular to the surface plane, as a result of vertical phase separation, directed by the substrate. These variations propagate to a higher degree through the film for the polymers with a larger fraction of modified side chains. The surface composition of the films is studied by Near-edge X-ray absorption fine structure spectroscopy (NEXAFS). Quantitative analysis of the NEXAFS spectra through a linear combination fit with the spectra of the pure components yields the surface composition. The resulting blend ratios reveal polymer-enrichment of the film surface for all three blends, which also becomes stronger as the polar character of the polymer increases. Comparison of the NEXAFS spectra collected with two different sampling depths shows that the vertical composition gradient builds up already in the first nanometers underneath the surface of the films. The results obtained with this new series of polymers shed light on the onset of formation of lamellar structures in thin polymer:PCBM films prepared from highly volatile solvents.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.