The objective of this study was to evaluate the surface roughness (SR), contact angle (CA), depth distribution of the charge particles (DDCP), mapping of chemical elements, 3D microtopography (3DM), and the micromorphology of the composites (MOR) of conventional and bulk fill after additional polishing. The specimens were prepared from Filtek Bulk Fill (FBF), Tetric N‐Ceram Bulk Fill (TNCBF), Opus Bulk Fill (OBF), X‐tra Fil (XTFL), Filtek Z250 XT (XT), Grandioso (GRA), Tetric N‐Ceram (TNC), Vittra APS (VT), according to three additional techniques (n = 10): without finishing and polishing, finishing and polishing with abrasive rubbers (Astropol), finishing and polishing with Astropol plus additional polishing with silicon carbide brush. The SR and CA were measured using a profilometer and adapted goniometer, respectively; 3DM used atomic force microscopy (AFM); the micromorphology and DDCP by scanning electron microscopy (SEM) and the MOR by means of X‐ray dispersive energy spectroscopy (EDS). The SR and CA were analyzed by ANOVA‐two factors and Tukey test (p < .05); the others data were analyzed descriptively. The DDCP of all the resins had an organic matrix rich surface layer and a particulate rich subsurface layer of smaller dimensions. Additional polishing: reduced SR of FBF, VT, TNCBF, and XTFL resins; increased the CA value of the XTFL and decreased of XT. In the analyzes for 3DM, smoother and more uniform surfaces were observed in all a resins. The elements: carbon (predominant), oxygen, silicon, zirconia, and aluminum were present in all composite resins. Therefore, additional polishing improved the surface properties of the resins studied.

The tackiness presented by resins brings inconveniences to the incremental technique, which can be improved by using lubricants in handling. Aim: To evaluate the influence of two adhesive systems as brush lubricants on the degree of conversion, translucency and intrinsic color stability of composite resins. Methods: Samples (n=10) were fabricated according to the composites (Filtek Z350 XT, IPS Empress Direct, and Esthet X HD), shades (bleach shade and A2), and lubricants used (Adper Single Bond 2, Scotchbond Multi-Purpose bonding agent, and no lubricant). Single composite increments were inserted into a Teflon mold. The composite surface was then modeled using a brush dipped in an adhesive system. The control group was fabricated with no additional modeling. The surface degree of conversion (DC) was measured using Fourier transform infrared spectroscopy; translucency and intrinsic color stability were accessed using a spectrophotometer. Data were analyzed using three-way ANOVA and the Tukey test (p<0.05). Results: Scotchbond Multi-Purpose decreased the DC of all composites and shades in comparison with the control group (p<0.05), although it did not decrease color stability (p<0.05). The bleach shade of IPS Empress Direct and Esthet X HD showed higher translucency than the A2 shade when lubricated with the adhesive systems (p<0.05). Conclusion: Therefore, the two tested adhesive systems used as brush lubricants on composites promoted changes to the surface degree of conversion and aesthetic properties.

<p><strong>Objective: </strong>This study analyzed the effect of two light emitting diodes (LEDs) on the degree of conversion (DC) of a composite resin for bleached teeth under the influence of adhesives systems used as modeling liquid. <strong>Material and methods: </strong>A total of 60 samples of IPS Empress Direct resin (Ivoclar, Vivadent) in BL-L shade were made in a single increment and polymerized for 20 seconds. The treatments were: 1) Type of adhesive used as modeling liquid (Adper Single Bond 2; the bond component of Adper Scotchbond Multi-Purpose; or no adhesive systems used as modeling liquid were used in the control group); and 2) Type of LED (Bluephase, polywave; and Coltolux, monowave). The DC, percentage of monomers converted to polymer during polymerization, was were evaluated using Fourier Transform Infrared Spectroscopy (FTIR) with 10 scans and wavenumber related to 1/λ for observation of the peaks at 1608 and 1638 cm^-1. Data were statistically analyzed by two-way analysis of variance (ANOVA) with Tukey's test (<em>p</em>&lt; 0.05). <strong>Results:</strong> There was no statistical difference between LEDs in comparison to the treatments (<em>p</em>&gt; 0.05). However, there was a statistically significant increase in the DC for the adhesive systems tested in comparison to the control group (<em>p</em>&lt; 0.05), with the highest values for Single Bond 2. <strong>Conclusion:</strong> It is concluded that the use of adhesives as modeling liquid of Empress Direct resin for bleached teeth shade increases the degree of conversion of the composite surface, and that curing with both kinds of LEDs does not interfere in this property.</p><p><strong> </strong></p><p><strong>Keywords</strong></p><p><strong></strong>Composite resins; Dentin-bonding agents; Surface properties.</p>

No abstract

No abstract