Despite the increasing percentages of children who are overweight, few studies have investigated their gait patterns. The purpose of this study was to quantify the three-dimensional knee joint kinematics and kinetics during walking in children of varying body mass and to identify effects associated with obesity. Three-dimensional kinematics and kinetics were collected from children of normal weight and overweight during normal gait using surface-mounted infrared emitting diodes and a force plate. The overweight group walked with a significantly lower peak knee flexion angle during early stance, and no significant differences in peak internal knee extension moments were found between groups. However, the overweight group showed a significantly higher peak internal knee abduction moment during early stance. These data suggest that although overweight children may develop a gait adaptation to maintain a similar knee extensor load, they may not be able to compensate for alterations in the frontal plane, which may lead to increased medial compartment joint loads. Therefore, assuming that the development of varus angular deformities of the knee joint and, in the longer term, medial compartment osteoarthritis are influenced by cumulative stress, this study supports the understanding that childhood obesity may impart a greater risk for the development of these diseases.

This study investigated the role of the material properties assumed for articular cartilage, meniscus and meniscal attachments on the fit of a finite element model (FEM) to experimental data for meniscal motion and deformation due to an anterior tibial loading of 45 N in the anterior cruciate ligament-deficient knee. Taguchi style L18 orthogonal arrays were used to identify the most significant factors for further examination. A central composite design was then employed to develop a mathematical model for predicting the fit of the FEM to the experimental data as a function of the material properties and to identify the material property selections that optimize the fit. The cartilage was modeled as isotropic elastic material, the meniscus was modeled as transversely isotropic elastic material, and meniscal horn and the peripheral attachments were modeled as noncompressive and nonlinear in tension spring elements. The ability of the FEM to reproduce the experimentally measured meniscal motion and deformation was most strongly dependent on the initial strain of the meniscal horn attachments (epsilon(1H)), the linear modulus of the meniscal peripheral attachments (E(P)) and the ratio of meniscal moduli in the circumferential and transverse directions (E(theta)E(R)). Our study also successfully identified values for these critical material properties (epsilon(1H) = -5%, E(P) = 5.6 MPa, E(theta)E(R) = 20) to minimize the error in the FEM analysis of experimental results. This study illustrates the most important material properties for future experimental studies, and suggests that modeling work of meniscus, while retaining transverse isotropy, should also focus on the potential influence of nonlinear properties and inhomogeneity.

Our objective was to characterize variations in mechanical knee alignment, tibial torsion, tibial width, and ACL laxity measurements between Japanese and Caucasian populations in the healthy, young adult knee joint. Seventy young adult subjects participated in this study, including 23 Japanese and 47 Caucasian subjects. Coronal magnetic resonance images of the hip, knee, and ankle were acquired for analysis. Japanese subjects had a significantly higher (p ¼ 0.04) varus alignment (1.64 AE 0.438 standard error) than Caucasians (0.55 AE 0.338), while women exhibited a more valgus alignment (0.16 AE 0.528) than men (0.94 AE 0.428, p ¼ 0.04). Significant differences were found in tibial torsion and ACL laxity (p < 0.01) between ethnicities, with Japanese exhibiting lower tibial torsion (33.4 AE 10.08) and higher ACL laxity (7.5 AE 0.4 mm) measurements compared to Caucasians (38.9 AE 9.58 and 5.7 AE 0.3 mm, respectively). Significant differences between genders were found in hip-knee-ankle alignment (p ¼ 0.04), tibial width (p < 0.0001), and ACL laxity (p < 0.01) measurements. Measurements were reliable between observers and for repeated positioning. Our study provides new insight into anatomical and geometric differences in the knee joint between Japanese and Caucasians, as well as between females and males. Further consideration of these results may improve development of implants to accommodate for these differences, and understanding of characteristics leading to increased prevalence of knee OA in certain populations. The use of magnetic resonance imaging to obtain these measurements also allows soft tissue structure characterization without exposure to ionizing radiation. ß

Although the rabbit hindlimb has been commonly used as an experimental animal model for studies of osteoarthritis, bone growth and fracture healing, the in vivo biomechanics of the rabbit knee joint have not been quantified. The purpose of this study was to investigate the kinematic and kinetic patterns during hopping of the adult rabbit, and to develop a model to estimate the joint contact force distribution between the tibia1 plateaus. Force platform data and three-dimensional motion analysis using infrared markers mounted on intracortical bone pins were combined to calculate the knee and ankle joint intersegmental forces and moments. A statically determinate model was developed to predict muscle, ligament and tibiofemoral joint contact forces during the stance phase of hopping. Variations in hindlimb kinematics permitted the identification of two landing patterns, that could be distinguished by variations in the magnitude of the external knee abduction moment. During hopping, the prevalence of an external abduction moment led to the prediction of higher joint contact forces passing through the lateral compartment as compared to the medial compartment of the knee joint. These results represent critical data on the in vivo biomechanics of the rabbit knee joint, which allow for comparisons to both other experimental animal models and the human knee, and may provide further insight into the relationships between mechanical loading, osteoarthritis, bone growth, and fracture healing.

The purpose of this study was to clarify meniscal displacement and cartilage-meniscus contact behavior in a full extension position and a deep knee flexion position. We also studied whether the meniscal translation pattern correlated with the tibiofemoral cartilage contact kinematics. Magnetic resonance (MR) images were acquired at both positions for 10 subjects using a conventional MR scanner. Subjects achieved a flexion angle averaging 1398 AE 38. Both medial and lateral menisci translated posteriorly on the tibial plateau during deep knee flexion. The posterior translation of the lateral meniscus (8.2 AE 3.2 mm) was greater than the medial (3.3 AE 1.5 mm). This difference was correlated with the difference in tibiofemoral contact kinematics between medial and lateral compartments. Contact areas in deep flexion were approximately 75% those at full extension. In addition, the percentage of area in contact with menisci increased significantly due to deep flexion. Our results related to meniscal translation and tibio-menisco-femoral contact in deep knee flexion, in combination with information about force and pressure in the knee, may lead to a better understanding of the mechanism of meniscal degeneration and osteoarthritis associated with prolonged kneeling and squatting. ß