Additive Manufacturing (AM) is gaining prominence due to its massive advantage in fabricating components without any geometrical limitations. The most widely used AM technique is Fused Deposition Modelling (FDM). FDM is an extrusion-based AM mostly focused on producing functional prototypes and in some cases as an end-product. One of the most common challenges associated with FDM is its reduced dimensional accuracy and surface quality. A fair amount of research has been carried out to identify the factors affecting print quality and measures to reduce surface roughness. On a few occasions, it is still necessary to achieve higher precision and quality to meet the standards set by conventional manufacturing. Hence, post-processing is employed as an additional step to reach the finish required. This paper focuses on enhancing the surface quality of FDM parts by subjecting it to Acetone vapour smoothening, Shot-blasting and Laser-assisted finishing post-processing methods. A comparative study is presented in this paper, where surface produced by different post-processing methods were compared to the reference injection moulding components. The results suggest that the acetone-based process has the best surface finish compared to the other two means; however, it leaves a very glossy appearance to the part. Shot blasting is very aggressive, and blasting time has a strong influence on the part quality. Laser-assisted finishing slightly ignites the top layer during melting leading to discolouration of the part. The optimum solution was found to be combining the post-processes, which not only reduced the roughness but also enhanced the aesthetic properties of the product.
Automotive interior components are produced by injection moulding due to its cost effectiveness in mass production. The surfaces of these components are textured to control the appearance and other surface functional properties such as wear and scratch resistance. Key challenges lie in replicating the features of mould tool with high aspect ratio which are influenced by the polymer and large number of process variables. Hence, to control the aesthetic properties, it is important to improve the understanding of the replication of textured surfaces and its relationship with measured gloss. In this study, the surface topography of PC-ABS samples is investigated using coherence scanning interferometry. Replication of two types- coarse and fine grain surface texture are investigated to identify the effects of tool temperature, injection speed and holding pressure. Areal surface parameters are scrutinized for the quantitative characterization and discrimination of study samples surface topographies. The correlations between process parameters, measured gloss and areal surface parameters are discussed. The results show significant influence of process variables on the replication of surface topography and measured gloss. The grain pattern governed the set of surface parameters selected and the variation in gloss. The process variables are observed to influence different region or distribution of specific surface features represented by surface parameters.
Manufactured surfaces usually consist of topographical features which include both those put forth by the manufacturing process, and microfeatures caused by disturbances during this process. Surface characterization basically involves study of these features which influence the functionality of the surface. This article focuses on characterization of the surface topography of machined lead brass and lead free brass. The adverse effect of lead on human health and the environment has led the manufacturing sector to focus on sustainable manufacturing of lead free brass, as well as how to maintain control of the surface integrity when substituting the lead content in the brass with silicon. The investigation includes defined areal surface parameters measured on the turned samples of lead and lead free brass using an optical coherence scanning interferometer, CSI. This paper deals with the study of surface topography of turned samples of lead and lead free brass. It is important to study the topographical characteristics of the brass samples which are the intermediate link between the manufacturing process variables and the functional behaviour of the surface. To numerically evaluate the sample's surface topography and to validate the measurements for a significant study, a general statistical methodology is implemented. The results indicate higher surface roughness in turned samples of lead brass compared to lead free brass.
A major drawback of the optical microscope is its limitation to resolve finer details. Many microscopes have been developed to overcome the limitations set by the diffraction of visible light. The scanning electron microscope (SEM) is one such alternative: it uses electrons for imaging, which have much smaller wavelength than photons. As a result high magnification with superior image resolution can be achieved. However, SEM generates 2D images which provide limited data for surface measurements and analysis. Often many research areas require the knowledge of 3D structures as they contribute to a comprehensive understanding of microstructure by allowing effective measurements and qualitative visualization of the samples under study. For this reason, stereo photogrammetry technique is employed to convert SEM images into 3D measurable data. This paper aims to utilize a stereoscopic reconstruction technique as a reliable method for characterization of surface topography. Reconstructed results from SEM images are compared with coherence scanning interferometer (CSI) results obtained by measuring a roughness reference standard sample. This paper presents a method to select the most robust/consistent surface texture parameters that are insensitive to the uncertainties involved in the reconstruction technique itself. Results from the two-stereoscopic reconstruction algorithms are also documented in this paper.
The increasing interest in Additive Manufacturing (AM) is due to its huge advantage in producing parts without any geometrical limitations. It is due to this reason, AM is extensively utilized in automotive, aerospace, medical and dental applications. Despite their popularity, AM is often associated with inferior surface quality which is one of the many reasons why it has failed to fully replace traditional methods. Hence, AM is always followed by a subsequent post-processing step to produce the end-product. To establish control over the surface quality it is first necessary to fully understand the surface behaviour concerning the factors affecting it. In this paper, the focus is mainly on having a better understanding of the surfaces by using scale-sensitive fractal analysis. In addition, the paper documents the influence of build inclination and post-processing in particular shot blasting on surface topography and utilizes a multi-scale approach to identify the most important scale and parameters for characterization. Results of this study reveal that shot blasting has a minimalistic effect on surface features at a large scale as it cannot remove the waviness completely. At smaller scales, blasting imparts additional features on the surface due to the impact of abrasive particles at high pressure. At the intermediate scales, the influence of shot blasting is highest as it successfully eliminates the surface features comprising of partially melted powder particles and stair-step effect.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.