Delivery of drugs into eyes using conventional drug delivery systems, such as solutions, is a considerable challenge to the treatment of ocular diseases. Drug loss from the ocular surface by lachrymal fluid secretion, lachrymal fluid-eye barriers, and blood-ocular barriers are main obstacles. A number of ophthalmic drug delivery carriers have been made to improve the bioavailability and to prolong the residence time of drugs applied topically onto the eye. The potential use of microemulsions as an ocular drug delivery carrier offers several favorable pharmaceutical and biopharmaceutical properties such as their excellent thermodynamic stability, phase transition to liquid-crystal state, very low surface tension, and small droplet size, which may result in improved ocular drug retention, extended duration of action, high ocular absorption, and permeation of loaded drugs. Further, both lipophilic and hydrophilic characteristics are present in microemulsions, so that the loaded drugs can diffuse passively as well get significantly partitioned in the variable lipophilic-hydrophilic corneal barrier. This review will provide an insight into previous studies on microemulsions for ocular delivery of drugs using various nonionic surfactants, cosurfactants, and associated irritation potential on the ocular surface. The reported in vivo experiments have shown a delayed effect of drug incorporated in microemulsion and an increase in the corneal permeation of the drug.

No abstract

Objective. The objective of this work encompasses the application of the response surface approach in the development of buccoadhesive pharmaceutical wafers of Loratadine (LOR). Methods. Experiments were performed according to a 32 factorial design to evaluate the effects of buccoadhesive polymer, sodium alginate (A), and lactose monohydrate as ingredient, of hydrophilic matrix former (B) on the bioadhesive force, disintegration time, percent (%) swelling index, and time taken for 70% drug release (t 70%). The effect of the two independent variables on the response variables was studied by response surface plots and contour plots generated by the Design-Expert software. The desirability function was used to optimize the response variables. Results. The compatibility between LOR and the wafer excipients was confirmed by differential scanning calorimetry, FTIR spectroscopy, and X-ray diffraction (XRD) analysis. Bioadhesion force, measured with TAXT2i texture analyzer, showed that the wafers had a good bioadhesive property which could be advantageous for retaining the drug into the buccal cavity. Conclusion. The observed responses taken were in agreement with the experimental values, and Loratadine wafers were produced with less experimental trials, and a patient compliant product was achieved with the concept of formulation by design.

Hydroxy propyl methyl cellulose (HPMC) 5cPs, an aqueous soluble polymer was employed for coating diclofenac sodium (DFS) tablets 25 mg for protecting the integrity of the drug yet rendering the drug to release at a faster rate on contact with the gastric environment. Proper optimization for the aqueous based film coating formulation was undertaken primarily employing plasticizers like polyethylene glycol (PEG) 400 and propylene glycol (PG). The defect free selected formulations were further subjected for studying the effects of surfactants like sodium lauryl sulphate (SLS) and Tween-80 along with the plasticizers. The quality of the aqueous film coats or the plasticizer efficiency in case of PEG-400 is in the order 1.5 > 0.5 > 1.0% and for PG 1 > 4 > 3% which can be stated on the basis of less incidence of major coat defects like chipping, cracking, orange peel, roughness, blistering, blooming, picking. The quality of aqueous film coat or the surfactant efficiency in case of SLS + PEG-400 is in the order 0.3 < 0.5 < 0.1% and SLS + PG is in the order 0.5 < 0.1 < 0.3%. In case of Tween-80 + PEG-400 the order is 0.3 < 0.5 < 0.1% and Tween-80 + PG is in the order 0.3 < 0.1 < 0.5%. Elegant film formation can be stated from fewer incidences of coat defects. The obtained coated tablets eventually satisfied all the normal physical parameters like thickness, weights, and weight gain, drug content, crushing strength, percent friability, disintegration time, dissolution profile and possible drug-polymer interactions. ANOVA was undertaken followed by Dunnet multiple comparison for the dissolution profile considering uncoated as the standard. The difference was considered significant at p ⩽ 0.01.

No abstract