This in vitro study evaluated the shear bond strength (SBS) between ceramic brackets (CBs) and resin composite restorations (RCRs) prepared using different surface treatments. The findings were also compared with a similar study that used stainless steel brackets (SSBs). Forty-five premolars were restored with a nano-hybrid composite resin (Tetric EvoCeram) and randomly assigned to three surface treatment groups: group 1, 5 per cent hydrofluoric acid (HF); group 2, air abrasion (50 μm alumina particles); and group 3, diamond bur. Specimens were bonded with CBs (Fascination) and exposed to thermo-cycling (500 cycles). The shear force at a crosshead speed of 1 mm/minute was transmitted to brackets. The adhesive remnant index (ARIs) scores were recorded after bracket failure. The analysis of SBS variance (P < 0.01) and chi-square test of ARIs scores (P < 0.01) revealed significant differences among three groups tested. The SBS in group 3 (mean: 26.34 ± 4.76 MPa) and group 2 (mean: 26.68 ± 5.93 MPa) was significantly higher than group 1 (mean: 16.25 ± 5.42 MPa). The SBS was significantly higher in CBs (mean: 23.09 ± 7.19 MPa) compared to SSBs (mean: 15.56 ± 5.13 MPa). High ARIs (100 per cent) occurred in SSBs treated with a diamond bur, whereas CBs primarily failed at the resin-adhesive interface (P < 0.01). In two-thirds of the specimens (SSBs or CBs), no adhesive was left on the restoration after HF conditioning. The ARIs profile of CBs and SSBs that received surface treatments with air abrasion were similar (P > 0.05) and bond failure occurred mainly in adhesive-bracket base and resin-adhesive interfaces. The diamond bur surface treatment is recommended as a safe and cost-effective method of bonding CBs to RCRs.

Air abrasion has a greater effect than CO₂and Er,Cr:YSGG lasers in the treatment of zirconia ceramic surfaces to enhance the bonding strength of resin cement to zirconia. CO₂laser at 4W and Er,Cr:YSGG laser at only 3-W output power can be regarded as surface treatment options for roughening the zirconia surface to establish better bond strength with resin cements.

No abstract

Aim:The aim was to evaluate the effect of sugar-free chewing gum containing casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) and xylitol on salivary Streptococcus mutans.Materials and Methods:A total of 60 dental students of 20-25 years old, who volunteered after checking their health condition and signing an informed consent, were randomly allocated to receive one of the following interventions: (A) Chewing gum containing CPP-ACP; (B) containing xylitol. Subjects within the experimental groups were taken the gums 3 times daily, after each meal for a period of 3 weeks. Pre- and post-intervention unstimulated saliva samples were quantified for S. mutans counts.Results:A statistically significant reduction of salivary S. mutans was displayed in both groups A and B after the intervention when compared with baseline (P < 0.001), and group A shows more statistically significant reduction of salivary S. mutans than group B (P = 0.011).Conclusion:Daily consumption of chewing gum containing CPP-ACP and xylitol significantly reduces the level of salivary S. mutans, but chewing gum containing CPP-ACP can reduce the level of salivary S. mutans in more than xylitol chewing gum.

Since octafluoropentyl methacrylate is an antifouling polymer, surface modification of polyether ether ketone with octafluoropentyl methacrylate is a practical approach to obtaining anti-biofilm biocompatible devices. In the current study, the surface treatment of polyether ether ketone by the use of ultraviolet irradiation, so as to graft (octafluoropentyl methacrylate) polymer chains, was initially implemented and then investigated. The Fourier-transform infrared and nuclear magnetic resonance spectra corroborated the appearance of new signals associated with the fluoroacrylate group. Thermogravimetric curves indicated enhanced asymmetry in the polymer structure due to the introduction of the said new groups. Measuring the peak area in differential scanning calorimetry experiments also showed additional bond formation. Static water contact angle measurements indicated a change in wettability to the more hydrophobic surface. The polyether ether ketone-octafluoropentyl methacrylate surface greatly reduced the protein adsorption. This efficient method can modulate and tune the surface properties of polyether ether ketone according to specific applications.