Saat ini, beton dengan menggunakan agregat ringan dapat mencapai kuat tekan 17 - 41 MPa. Di Cilacap terdapat industri penghasil agregat ringan yang mempunyai karakteristik material cocok untuk beton yaitu agregat ALWA Cilacap. Penelitian ini akan menggunakan agregat ALWA Cilacap untuk mensubtitusi agregat kasar pada beton sehingga dapat menghasilkan beton mutu tinggi yang ringan. Metodologi yang digunakan dalam penelitian ini dengan melakukan eksperimen di laboratorium. Persentase penggunaan agregat ringan ALWA – Cilacap untuk mensubstitusi agregat kasar sebesar 0%, 5%, 10%, 15% dan 20%. Pengujian kuat tekan beton dan berat isi menggunakan benda uji silinder 150 x 300 mm. Hasil penelitian menunjukkan bahwa kuat tekan beton maksimum pada benda uji B4 (subtitusi agregat ringan ALWA-Cilacap 15% dari agregat kasar) sebesar 39,7 MPa. Berat isi yang paling ringan adalah pada benda uji B5 (subtitusi agregat ringan ALWA-Cilacap 20% dari agregat kasar) yaitu sebesar 2.151 gr/cm3.
Increasing capacity of structures can be done by various methods, one of them is by reinforcing on bridge structure.Reinforcement by using strand has been used on building construction but on reinforced concrete beams because of the problems on it’s execution. The focus of this research is how to install non-stressing strand as reinforcement material.The basic of the research is full-scalled loading test on structure laboratory. There are 2 loading test samples : a sample without reinforcement (Bo) and a sample with reinforcement(B1). The test specimen will be subjected to static monotonic loading until the collapse. The dimensions of the test specimen are 150 x 300 (mm) and the length of the span is 3200 mm.The result of loading for the reinforced concrete beam and reinforcement beam, the yield force value was 22 kN and 27 kN respectively, while deflection value was 9.5 mm and 13 mm respectively.Keywords: beam, reinforcement, strand without stressing, static load.ABSTRAKPeningkatan kemampuan(kapasitas) infrastruktur khususnya jembatan dapat dilakukan dengan berbagai metode, salah satu untuk meningkatkan kemampuan tersebut dengan memperkuat jembatan.Perkuatan menggunakan strand sudah digunakan pada berbagai konstruksi bangunan tetapi untuk balok beton bertulang belum banyak dilakukan karena akan mengalami kesulitan dalam metode pelaksanaan. Sehingga dalam penelitian ini akan mencoba menggunakan metode pemasangan strand tanpa penegangan sebagai bahan perkuatan.Penelitian dilakukan dengan cara pengujian eksperimental di laboratorium dan. Benda uji yang digunakan terdiri dari 2(dua) buah yaitu 1(satu) benda uji balok beton bertulang tanpa perkuatan(Bo) dan 1(satu) buah benda uji balok beton bertulang dengan perkuatan(B1). Benda uji akan dilakukan uji pembebanan statikmonotonik sampai mengalami keruntuhan. Dimensi benda uji 150 x 300 (mm) dan panjang bentang 3200 mm.Dari hasil pengujian terhadap balok beton tanpa perkuatan dan balok perkuatan didapatkan nilai gaya leleh berturut – turut sebesar 22kN dan 27kN serta lendutan berturut –turut sebesar 9.5 mm dan 13 mm.Kata kunci : balok, perkuatan, strand tanpa penegangan, beban statik
Many methods can be used in the repair of bridges or other structural buildings. The aim is to increase the existing capacity. In the reinforced concrete beam structure, capacity of structural elements can be carried out by reinforcement method. The research was done by experimental loading test in laboratory. The test objects are consisted of 2 (two) reinforced concrete beams: a normal beam without reinforcement (NB) and a reinforcement beam by using non-stressing srand (RB1). The dimensions of the beams are 150mm x 300mm x 3200 mm. All beams are loaded by static-monotonic load until collapses. From the results of the research, the first yield load for the NB beam and RB1 beam respectively are 22 kN and 29kN. The deformations that occur at the conditions are 9.5mm and 14mm respectively. The collapse occurring on the NB beam is the bending collapse, whereas in the RB1 beam is a bending- shear collapse.
Reinforcing method of reinforced concrete beam has been done in Indonesia, one of them is by using of strand stressing. Strandstressing need additional technology so that strand reinforcing is not much in demand. Strand has high strength, so using strand needs to be modified in order to take advantage of the material. In this study, the strand will be used to reinforce of reinforced concrete beam by using epoxy and U-steel as anchors.The research methodology based on experimental in the laboratory. The samples are consist of 3 specimens : the first is specimen without using of reinforcement (BU01), the second is specimen with reinforcement by using epoxy and 3 U-steel as anchors(BU02), the third is specimen with reinforcement by using epoxy and 7 U-steel as anchors(BU03). Specimens dimensions of reinforced concrete beam are 150 mm x 300 mm with a span of 3000 mm.The results show that the initial crack occurred in mid span beam on the pull side. The loads causing initial crack as follow: at BU01 = 6.22 kN, at BU02 = 3.95 kN and at BU03 = 0.25 kN. The results research show that initial cracking load of the specimen is inversely proportional with the number of anchor. If the number of anchor is greater, the cracking load will be smaller.Keywords: reinforcement beam, steel of strand, initial crackABSTRAKMetode perkuatan balok beton bertulang sudah banyak dilakukan di Indonesia, salah satunya menggunakan baja strand yang ditegangkan. Penggunaan baja strand sebagai perkuatan masih terbatas dengan melakukan penegangan. Penegangan pada strand memerlukan teknologi tambahan sehingga perkuatan menggunakan strand tidak banyak diminati untuk perkuatan. Mengingat kekuatan strand yang tinggi maka pemanfaatan strand perlu dilakukan modifikasi agar dapat mengambil kelebihan dari material tersebut. Pada penelitian ini pemanfaatan strand digunakan untuk perkuatan balok bertulang tanpa dilakukan penegangan tetapi diikat dengan epoxy dan baja U yang diangkurkan ke balok beton bertulang.Metodologi penelitian yang digunakan menggunakan experimental di laboratorium. Benda uji terdiri dari 3 buah yaitu benda uji normal tanpa menggunakan perkuatan (BU01), benda uji dengan perkuatan strand tanpa penegangan yang diikat dengan epoxy dan 3 baja U yang diangkurkan ke balok beton bertulang (BU02) dan benda uji dengan perkuatan strand tanpa penegangan yang diikat dengan epoxy dan 7 baja U yang diangkurkan ke balok beton bertulang (BU03). Dimensi benda uji balok beton bertulang adalah 150 mm x 300 mm dengan bentang 3000 m.Hasil penelitian menunjukkan bahwa retak awal terjadi di tengah bentang (mid span) balok pada sisi tarik. Beban yang menyebabkan retak awal pada BU01 = 6,22 kN, BU02 = 3,95 kN dan BU03 = 0,25 kN. Hasil tersebut menunjukkan bahwa benda uji yang mempunyai lubang angkur untuk mengikat strand semakin banyak maka beban yang menyebabkan retak awal semakin kecil.Kata Kunci : perkuatan balok, baja strand, retak awal
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.