The purpose of this study is to evaluate the effect of pulp chamber extension angles and filling material mechanical properties on the biomechanical response of a ceramic endocrown. A 3D model of maxillary molar that underwent endodontically treatment was exported to computer aided design software to conduct finite element analysis (FEA). The endocrown model was modified considering different pulp chamber extension angles (right angle; 6°, 12° and 18° of axial divergence). The solids were imported into the computer aided engineering software in Standard for the Exchange of Product Data (STEP) format. Nine different filling materials were simulated to seal the orifice of the root canal system under each endocrown restoration (resin composite, bulk-fill resin composite, alkasite, flowable resin composite, glass ionomer cement, autocured resin-reinforced glass ionomer cement, resin cement, bulk-fill flowable resin composite, zinc oxide cement), totaling 36 models. An axial load (300 N) was applied at the occlusal surface. Results were determined by colorimetric graphs of von-Misses stress (VMS) and Maximum Principal Stress (MPS) on tooth, cement layer, and endocrown restorations. VMS distribution showed a similar pattern between the models, with more stress at the load region for the right-angled endocrowns. The MPS showed that the endocrown intaglio surface and cement layer showed different mechanical responses with different filing materials and pulp chamber angles. The stress peaks plotted in the dispersion plot showed that the filling material stiffness is proportional to the stress magnitude in the endocrown, cement layer and tooth adhesive surface. In addition, the higher the pulp chamber preparation angle, the higher the stress peak in the restoration and tooth, and the lower the stress in the cement layer. Therefore, 6° and 12° pulp chamber angles showed more promising balance between the stresses of the adhesive interface structures. Under the conditions of this study, rigid filling materials were avoided to seal the orifice of root canal system when an endocrown restoration was planned as rehabilitation. In addition, the pulp chamber axial walls were prepared between 6° and 12° of divergence to balance the stress magnitude in the adhesive interface for this treatment modality.

The endodontic revascularization may be an alternative treatment for necrotic immature teeth, however, several treatment steps may cause tooth discoloration. This study evaluated the use of three calcium silicate-based cements with different radiopacifying agents on the color alteration (∆E) of extracted premolars after simulation of revascularization. Forty single rooted extracted premolars were shaped with #1-6 gates Glidden drills, rinsed with sodium hypochlorite, and filled with fresh human blood. Three calcium silicate-based cements with different radiopacifying agents (bismuth oxide - CSBi, calcium tungstate - CSW, and zirconium oxide - CSZr) were applied over the blood clot (n=10). The control group received the application of a temporary zinc oxide-based cement (TFZn) (n=10). ∆E was measured with a spectrophotometer, using the L*a*b* color system of the International Commission on Illumination (CIELab), in different times: prior to the preparation of the access cavity (t0); right after treatment (t1); and after one (t2), two (t3), three (t4) and four (t5) months. The tooth site for color evaluation was standardized by silicon matrix, the color reading was performed 3 times per tooth, and the teeth were stored in 37º water between evaluations. ∆E, whiteness (WID index) and yellowness (b*) were evaluated. Data were subjected to one-way ANOVA and repeated measures ANOVA, followed by Tukey’s post hoc test (α=0.05). All groups were similar in ∆E1 (t0-t1). The ∆E was the lowest and constant in the control group. In all evaluation times, CSBi presented the highest ∆E (p<0.01). CSW and CSZr were similar in all evaluated times and presented intermediate ∆E values. WID index from CSBi and CSW presented more distancing from ‘white’ reference. CSBi presented the greatest decrease in yellowness (b* value). The cement containing bismuth oxide presented the highest color alteration values. All tested calcium silicate-based cements presented clinically perceptible discoloration. Calcium tungstate and zirconium oxide may be used as alternative radiopacifiers to decrease tooth discoloration after endodontic tooth revascularization.

This study tested whether three different cement layer thicknesses (60, 120 and 180 μm) would provide the same bonding capacity between adhesively luted lithium disilicate and human dentin. Ceramic blocks were cut to 20 blocks with a low-speed diamond saw under cooling water and were then cemented to human flat dentin with an adhesive protocol. The assembly was sectioned into 1 mm2 cross-section beams composed of ceramic/cement/dentin. Cement layer thickness was measured, and three groups were formed. Half of the samples were immediately tested to evaluate the short-term bond strength and the other half were submitted to an aging simulation. The microtensile test was performed in a universal testing machine, and the bond strength (MPa) was calculated. The fractured specimens were examined under stereomicroscopy. Applying the finite element method, the residual stress of polymerization shrinkage according to cement layer thickness was also calculated using first principal stress as analysis criteria. Kruskal–Wallis tests showed that the ‘‘cement layer thickness’’ factor significantly influenced the bond strength results for the aged samples (p = 0.028); however, no statistically significant difference was found between the immediately tested groups (p = 0.569). The higher the cement layer thickness, the higher the residual stress generated at the adhesive interface due to cement polymerization shrinkage. In conclusion, the cement layer thickness does not affect the immediate bond strength in lithium disilicate restorations; however, thinner cement layers are most stable in the short term, showing constant bond strength and lower residual stress.