Alphaviruses have the ability to induce cell-cell fusion after exposure to acid pH. This observation has served as an article of proof that these membrane-containing viruses infect cells by fusion of the virus membrane with a host cell membrane upon exposure to acid pH after incorporation into a cell endosome. We have investigated the requirements for the induction of virus-mediated, low pH-induced cell-cell fusion and cell-virus fusion. We have correlated the pH requirements for this process to structural changes they produce in the virus by electron cryo-microscopy. We found that exposure to acid pH was required to establish conditions for membrane fusion but that membrane fusion did not occur until return to neutral pH. Electron cryo-microscopy revealed dramatic changes in the structure of the virion as it was moved to acid pH and then returned to neutral pH. None of these treatments resulted in the disassembly of the virus protein icosahedral shell that is a requisite for the process of virus membrane-cell membrane fusion. The appearance of a prominent protruding structure upon exposure to acid pH and its disappearance upon return to neutral pH suggested that the production of a "pore"-like structure at the fivefold axis may facilitate cell penetration as has been proposed for polio (J. Virol. 74 (2000) 1342) and human rhino virus (Mol. Cell 10 (2002) 317). This transient structural change also provided an explanation for how membrane fusion occurs after return to neutral pH. Examination of virus-cell complexes at neutral pH supported the contention that infection occurs at the cell surface at neutral pH by the production of a virus structure that breaches the plasma membrane bilayer. These data suggest an alternative route of infection for Sindbis virus that occurs by a process that does not involve membrane fusion and does not require disassembly of the virus protein shell.

Several factors, including spatial and temporal coherence of the electron microscope, specimen movement, recording medium, and scanner optics, contribute to the decay of the measured Fourier amplitude in electron image intensities. We approximate the combination of these factors as a single Gaussian envelope function, the width of which is described by a single experimental B-factor. We present an improved method for estimating this Bfactor from individual micrographs by combining the use of X-ray solution scattering and numerical fitting to the average power spectrum of particle images. A statistical estimation from over 200 micrographs of herpes simplex virus type-1 capsids was used to estimate the spread in the experimental B-factor of the data set. The B-factor is experimentally shown to be dependent on the objective lens defocus setting of the microscope. The average Bfactor, the X-ray scattering intensity of the specimen, and the number of particles required to determine the structure at a lower resolution can be used to estimate the minimum fold increase in the number of particles that would be required to extend a single particle reconstruction to a specified higher resolution. We conclude that microscope and imaging improvements to reduce the experimental Bfactor will be critical for obtaining an atomic resolution structure.

International audienceWe present a new algorithm for solving energy balance in phase change problems, particularly in solidification with macrosegregation. The algorithm is based on a nonlinear temperature evaluation using the average enthalpy which is provided by (i) tabulated phase transformation paths and (ii) tabulated phase properties. The compatibility of this method with tabulations using a thermodynamic database, allows simulating solidification at equilibrium with multiple phase transformations for binary and multicomponent alloys. The method has been validated and applied to three-dimensional cases with macrosegregation: a binary Sn–3 wt.% Pb alloy and a ternary Fe–2 wt.% C–30 wt.% Cr alloy. For the latter case, predictions include composition maps for C and Cr due to thermosolutal instability leading to freckle formation and the subsequent distributions of liquid, BCC, FCC, M7C3 and Cementite phases. Compared with a previously published enthalpy method, the temperature-based energy solver shows similar accuracy and faster computational time

International audienceFreckles are common defects in industrial casting. They result from thermosolutal convection due to buoyancy forces generated from density variations in the liquid. The present paper proposes a numerical analysis for the formation of channel segregation using the three-dimensional (3D) cellular automaton (CA)—finite element (FE) model. The model integrates kinetics laws for the nucleation and growth of a microstructure with the solution of the conservation equations for the casting, while introducing an intermediate modeling scale for a direct representation of the envelope of the dendritic grains. Directional solidification of a cuboid cell is studied. Its geometry, the alloy chosen as well as the process parameters are inspired from experimental observations recently reported in the literature. Snapshots of the convective pattern, the solute distribution, and the morphology of the growth front are qualitatively compared. Similitudes are found when considering the coupled 3D CAFE simulations. Limitations of the model to reach direct simulation of the experiments are discussed