This paper is concerned with a quasi-3D design method for centrifugal compressor impeller in the meridional plane. The method links up a novel inverse design algorithm, called Ball-Spine Algorithm (BSA), and a quasi-3D analysis code. The Euler equation is solved on the meridional plane for a numerical domain of which some unknown boundaries (hub and shroud) are iteratively modified under the BSA until a prescribed pressure distribution is reached. In BSA, the unknown walls are composed of a set of virtual balls that move freely along the specified directions called spines. The difference between target and current pressure distribution causes to deform flexible boundary at each modification step. In order to validate the quasi-3D analysis code, an existing compressor is investigated by some experiments in which several static pressure points on the shroud, the flow parameters at the compressor inlet and outlet are measured. Comparison of the quasi-3D analysis results with experimental results shows good agreement. Also, a full 3D Navier-Stokes code is used to analyze the existing and designed compressor numerically. The results show that the momentum decrease near the shroud wall in the existing compressor is removed by hub-shroud modification resulting an improvement in performance by 0.6 percent.

No abstract

This paper presents numerical and experimental investigation of the performance and internal flow field characteristics of twin-entry radial inflow turbines at full and extreme partial admission conditions. The turbine is tested on a turbocharger test facility, which was developed for small and medium size turbochargers. Experimental results show that the lowest efficiency corresponds to extreme conditions. Therefore, flow field analyzing is employed to consider these conditions. The flow pattern in the volute and impeller of a twin-entry turbine is analyzed using an in-house fully three-dimensional viscous flow solver. The computational performance results are compared with the experimental results and good agreement is found. The flow field at the outlet of the turbine is investigated using a five-hole pressure probe; the numerical results are also compared with experimental measurements at the outlet of the rotor. For the volute, results show that lowest entropy gain factor corresponds to the extreme conditions, particularly when shroud side entry is fully closed. At the inlet of the rotor for equal admission conditions, the incidence angle is mostly in the optimum values. However, large variation in the incidence angle is seen in the extreme conditions, which lead to larger incidence losses and consequently a lower efficiency. In addition, entropy distribution contours corresponding to the exit plane are considered. For full admission, the location of low entropy gain factor at this plane occupies a region near the shroud side of suction surface as well as near the hub side of the pressure surface that corresponds to a region of high absolute flow angle. However, for the extreme cases, the low entropy gain factor occupies a relatively larger region near the shroud side than full admission. So, higher loss generation is noted at the extreme cases. Moreover, this entropy gain factor region is increased when shroud side entry is fully closed.

No abstract

In this research the design methods of radial flow compressor volutes are reviewed and the main criterions in volute primary designs are recognized and most effective ones are selected. The effective parameters i.e. spiral cross section area, circumferential area distribution, exit cone and tongue area of the compressor volute are parametrically studied to identifythe optimum values. A numerical model is prepared and verified through experimental data which are obtained from the designed turbocharger test rig. Different volutes are modeled and numerically evaluated using the same impeller and vane-less diffuser. For each model, the volute total pressure ratio, static pressure recovery and total pressure loss coefficients and the radial force on the impeller are calculated for different mass flow rates at design point and off-design conditions. The volute which shows better performanceand causes lower the net radial force on the impeller, at desiredmass flow rates is selected as an optimal one. The results show the volute design approach differences at the design point and off-design conditions. Improving the pressure ratio and reducing total pressure loss at design point, may result inthe worse conditions at off-design conditions as well as increasing radial force on the impeller.

In this paper the performance characteristics of turbocharger twin-entry radial inflow gas turbine with unsymmetrical volute and rotor tip diameter of 73.6 mm in steady state and under full and partial admission conditions are investigated. The employed method is based on one dimensional performance prediction which is developed for partial admission conditions. Furthermore this method is developed for unsymmetrical volute of the turbine considering flow specifications. Experimental investigation of the research carried out on special test facility under full and partial admission conditions for a wide range of speed. The comparison of experimental and modeling results shows good agreements. Interestingly, the turbine maximum efficiency occurs when the shroud side inlet mass flow is higher than that of hub side.

No abstract

No abstract