Recently, hemp-fiber-reinforced polymer (HFRP) composites have been developed to enhance the strength and ductility of normal and lightweight aggregate concrete along with recycled brick aggregate concrete. In addition, both experimental and analytical investigations have been performed to assess the suitability of the existing strength and strain models. However, the theoretical and analytical expressions to predict the stress–strain curves of HFRP-confined concrete were not developed. Therefore, the main objective of this study was to develop analytical expressions to predict the stress–strain curves of HFRP-confined waste brick aggregate concrete. For this purpose, a new experimental framework was conducted to examine the effectiveness of HFRP in improving the mechanical properties of concrete constructed with recycled brick aggregates. Depending on the strength of the concrete, two groups were formed, i.e., Type-1 concrete and Type-2 concrete. A total of sixteen samples were tested. The ultimate compressive strength and strain significantly increased due to HFRP confinement. Improvements of up to 272% and 457% in the ultimate compressive strength and strain were observed due to hemp confinement, respectively. To predict the ultimate compressive strength and strain of HFRP-confined concrete, this study investigated several existing analytical stress–strain models. Some of the strength models resulted in close agreement with experimental results, but none of the models could accurately predict the ultimate confined strain. Nonlinear regression analysis was conducted to propose expressions to predict the ultimate compressive strength and strain of HFRP-confined concrete. The proposed expressions resulted in good agreement with experimental results. An analytical procedure was proposed to predict the stress–strain curves of hemp-confined concrete constructed by partial replacement of natural coarse aggregates by recycled fired-clay brick aggregates. A close agreement was found between the experimental and analytically predicted stress–strain curves.
This study investigated the influence of CFRP composite wrapping techniques on the load–deflection and strain relationships of non-prismatic RC beams. A total of twelve non-prismatic beams with and without openings were tested in the present study. The length of the non-prismatic section was also varied to assess the effect on the behavior and load capacity of non-prismatic beams. The strengthening of beams was performed by using carbon fiber-reinforced polymer (CFRP) composites in the form of individual strips or full wraps. The linear variable differential transducers and strain gauges were installed at the steel bars to observe the load–deflection and strain responses of non-prismatic RC beams, respectively. The cracking behavior of unstrengthened beams was accompanied by excessive flexural and shear cracks. The influence of CFRP strips and full wraps was primarily observed in solid section beams without shear cracks, resulting in enhanced performance. In contrast, hollow section strengthened beams exhibited minor shear cracks alongside the primary flexural cracks within the constant moment region. The absence of shear cracks was reflected in the load–deflection curves of strengthened beams, which demonstrated a ductile behavior. The strengthened beams demonstrated 40% to 70% higher peak loads than control beams, whereas the ultimate deflection was increased up to 524.87% compared to that of the control beams. The improvement in the peak load was more prominent as the length of the non-prismatic section increased. A better improvement in ductility was achieved for the case of CFRP strips in the case of short non-prismatic lengths, whereas the efficiency of CFRP strips was reduced as the length of the non-prismatic section increased. Moreover, the load–strain capacity of CFRP-strengthened non-prismatic RC beams was higher than the control beams.
Given the excessive demolition of structures each year, the issues related to the generated structural waste are striking. Bricks being a major constituent in the construction industry, also hold a significant proportion of the construction waste generated annually. The reuse of this brick waste in new constructions is an optimal solution considering cost-effectiveness and sustainability. However, the problems related to the substandard peak stress and ultimate strain of concrete constructed with recycled brick aggregates (CRAs) limit its use in non-structural applications. The present study intends to improve the unsatisfactory mechanical characteristics of CRAs by utilizing low-cost glass fiber chopped strand mat (FCSM) sheets. The efficacy of FCSM sheets was assessed by wrapping them around CRA specimens constructed with different concrete strengths. A remarkable increase in the peak compressive stress and the ultimate strain of the CRA specimens were observed. For low, medium, and high strength CRAs, the ultimate strain improved by up to 320%, 308%, and 294%, respectively, as compared to the respective control specimens. Several existing analytical models were utilized to predict the peak compressive stress and ultimate strain of the CRAs strengthened using FCSM sheets. None of the considered models reproduced experimental results accurately. Therefore, equations were formulated using regression predicting the peak stress and ultimate strain of the CRAs confined with FCSM sheets. The predicted values were found to correlate well with the experimental values.
Many masonry structures are constructed with cement clay interlocking brick (CCIB) due to its added benefits. Recent research has demonstrated the vulnerability of brick masonry walls against seismic loading. Various strengthening materials and techniques are extensively used to improve the structural behavior of brick walls. Carbon fiber-reinforced polymer (CFRP) composites are the most popular strengthening material due to their advantages of easy application, lightweight qualities, and superior tensile strength. The current research work aimed to explore the cost-effective solutions and feasibility of CFRP composite-based strengthening techniques to improve the load-bearing capacity of CCIB walls. Various configurations and combinations of strengthening materials were investigated to customize the cost of repair and strengthening. The experimental results indicated that CFRP composites in combination with cement-sand (CS) mortar are an efficient strengthening material to enhance the strength and ultimate deflection of CCIB walls. The ultimate load-bearing capacity and axial deformation of the strengthened CCIB wall (using two layers of CFRP strips and CS mortar of 10 mm thickness) remained 171% and 190% larger than the unstrengthened CCIB wall. The conclusions of this study are expected to enhance the seismic performance of masonry buildings in developing countries. It should be noted that due to the reduced number of tested specimens, the results to be assumed as general considerations need a wider experimental campaign and a large numbers of tests for each strengthening typology.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.