No abstract

No abstract

The fibrous cap of an atherosclerotic plaque may be prone to rupture if the occurring stresses exceed the strength of the cap. Rupture can cause acute thrombosis and subsequent ischaemic stroke or myocardial infarction. A reliable prediction of the rupture probability is essential for the appropriate treatment of atherosclerosis. Biomechanical models, which compute stresses and strain, are promising to provide a more reliable rupture risk prediction. However, these models require knowledge of the local biomechanical properties of atherosclerotic plaque tissue. For this purpose, we examined human carotid plaques using indentation experiments. The test set-up was mounted on an inverted confocal microscope to visualise the collagen fibre structure during the tests. By using an inverse finite element (FE) approach, and assuming isotropic neo-Hookean behaviour, the corresponding Young's moduli were found in the range from 6 to 891kPa (median 30kPa). The results correspond to the values obtained by other research groups who analysed the compressive Young's modulus of atherosclerotic plaques. Collagen rich locations showed to be stiffer than collagen poor locations. No significant differences were found between the Young's moduli of structured and unstructured collagen architectures as specified from confocal collagen data. Insignificant differences between the middle of the fibrous cap, the shoulder regions, and remaining plaque tissue locations indicate that axial, compressive mechanical properties of atherosclerotic plaques are independent of location within the plaque.

BackgroundRupture of the cap of a vulnerable plaque present in a coronary vessel may cause myocardial infarction and death. Cap rupture occurs when the peak cap stress exceeds the cap strength. The mechanical stress within a cap depends on the plaque morphology and the material characteristics of the plaque components. A parametric study was conducted to assess the effect of intima stiffness and plaque morphology on peak cap stress.MethodsModels with idealized geometries based on histology images of human coronary arteries were generated by varying geometric plaque features. The constructed multi-layer models contained adventitia, media, intima, and necrotic core sections. For adventitia and media layers, anisotropic hyperelastic material models were used. For necrotic core and intima sections, isotropic hyperelastic material models were employed. Three different intima stiffness values were used to cover the wide range reported in literature. According to the intima stiffness, the models were classified as stiff, intermediate and soft intima models. Finite element method was used to compute peak cap stress.ResultsThe intima stiffness was an essential determinant of cap stresses. The computed peak cap stresses for the soft intima models were much lower than for stiff and intermediate intima models. Intima stiffness also affected the influence of morphological parameters on cap stresses. For the stiff and intermediate intima models, the cap thickness and necrotic core thickness were the most important determinants of cap stresses. The peak cap stress increased three-fold when the cap thickness was reduced from 0.25 mm to 0.05 mm for both stiff and intermediate intima models. Doubling the thickness of the necrotic core elevated the peak cap stress by 60% for the stiff intima models and by 90% for the intermediate intima models. Two-fold increase in the intima thickness behind the necrotic core reduced the peak cap stress by approximately 25% for both intima models. For the soft intima models, cap thickness was less critical and changed the peak cap stress by 55%. However, the necrotic core thickness was more influential and changed the peak cap stress by 100%. The necrotic core angle emerged as a critical determinant of cap stresses where a larger angle lowered the cap stresses. Contrary to the stiff and intermediate intima models, a thicker intima behind the necrotic core increased the peak cap stress by approximately 25% for the soft intima models. Adventitia thickness and local media regression had limited effects for all three intima models.ConclusionsFor the stiff and intermediate intima models, the cap thickness was the most important morphological risk factor. However for soft intima models, the necrotic core thickness and necrotic core angle had a bigger impact on the peak cap stress. We therefore need to enhance our knowledge of intima material properties if we want to derive critical morphological plaque features for risk evaluation.

No abstract