Two novel D–A (donor–acceptor) and one D–A–D small molecules containing mesitylborane as an acceptor and triphenylamine as a donor, linked through a thieno[3,2-b]thiophene π-conjugated spacer, are synthesized and characterized.
Organic-inorganic perovskite materials are attracting increasing attention for their use in high-performance solar cells due to their outstanding properties, such as long diffusion lengths, low recombination rate, and tunable bandgap. Finding an effective method of defect passivation is thought to be a promising route for improvements toward narrowing the distribution of the power conversion efficiency (PCE) values, given by the spread in the PCE over different devices fabricated under identical conditions, for easier commercialization. In this work, we add 2‐(4‐fluoroph-enyl)ethyl ammonium iodide (p-f-PEAI) into the bulk of a mixed cation lead halide perovskite (CH3NH3PbBr3)0.15(HC(NH2)2PbI3)0.85 thin film. We investigate the influence of different p-f-PEAI concentrations on the optical properties, morphology, crystal orientation, charge carrier dynamics, and device performance. We observe that introducing the proper amount of p-f-PEAI changes the preferential orientation of the perovskite crystals, promotes the strength of the crystal textures, and suppresses non-radiative charge recombination. Thus, we obtain a narrower distribution of the PCE of perovskite solar cells (PSCs) without sacrificing the PCE values reached. This is an important step toward better reproducibility to realize the commercialization of PSCs.
Perovskite solar cells (PSCs) have been developed as a promising photovoltaic technology because of their excellent photovoltaic performance. However, interfacial recombination and charge carrier transport losses at the surface greatly limit the performance and stability of PSCs. In this work, the fabrication of high-quality PSCs based on methylammonium lead iodide with excellent ambient stability is reported. An anionic surfactant, sodium dodecylbenzene sulfonate (SDBS), is introduced to simultaneously passivate the defect states and stabilize the cubic phase of the perovskite film. The SDBS located at grain boundaries and the surface of the active layer can effectively passivate under-coordinated lead ions and protect the perovskite components from water-induced degradation. As a result, a champion power conversion efficiency (PCE) of 19.42% is achieved with an open-circuit voltage (V OC ) of 1.12 V, a short-circuit current (J SC ) of 23.23 mA cm −2 , and a fill factor (FF) of 74% in combination with superior moisture stability. The SDBS-passivated devices retain 80% of their initial average PCE after 2112 h of storage under ambient conditions.
Crystal orientations are closely related to the behavior of photogenerated charge carriers and are vital for controlling the optoelectronic properties of perovskite solar cells. Herein, we propose a facile approach to reveal the effect of lattice plane orientation distribution on the charge carrier kinetics via constructing CsBr-doped mixed cation perovskite phases. With grazing-incidence wide-angle X-ray scattering measurements, we investigate the crystallographic properties of mixed perovskite films at the microscopic scale and reveal the effect of the extrinsic CsBr doping on the stacking behavior of the lattice planes. Combined with transient photocurrent, transient photovoltage, and spacecharge-limited current measurements, the transport dynamics and recombination of the photogenerated charge carriers are characterized. It is demonstrated that CsBr compositional engineering can significantly affect the perovskite crystal structure in terms of the orientation distribution of crystal planes and passivation of trap-state densities, as well as simultaneously facilitate the photogenerated charge carrier transport across the absorber and its interfaces. This strategy provides unique insight into the underlying relationship between the stacking pattern of crystal planes, photogenerated charge carrier transport, and optoelectronic properties of solar cells.
In this work, donor−acceptor (D−A) copolymers of thienothiophenes and dithienothiophenes, having 1,2,3‐triazole units were prepared via a click reaction. Their optoelectronic properties were explored systematically providing the optical and electrochemical band gaps varying from 2.2 to 2.8 eV. Density functional theory (DFT) investigations of the model compounds revealed the presence of an intramolecular charge transfer transition between the donor TT/DTT units and 1,2,3‐triazole acceptor group.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.