No abstract

Anionic surfactants are used in greater volume than any other surfactants because of their highly potent detergency and low cost of manufacture. However, they have not been used as templates for synthesizing mesoporous silica. Here we show a templating route for preparing mesoporous silicas based on self-assembly of anionic surfactants and inorganic precursors. We use aminosilane or quaternized aminosilane as co-structure-directing agent (CSDA), which is different from previous pathways. The alkoxysilane site of CSDA is co-condensed with inorganic precursors; the ammonium site of CSDA, attached to silicon atoms incorporated into the wall, electrostatically interacts with the anionic surfactants to produce well-ordered anionic-surfactant-templated mesoporous silicas (AMS). These have new structures with periodic modulations as well as two-dimensional hexagonal and lamellar phases. The periodic modulations may be caused by the coexistence of micelles that differ in size or curvature, possibly owing to local chirality. These mesoporous silicas provide a new family of mesoporous materials as well as shedding light on the structural behaviour of anionic surfactants.

We studied equilibrium adsorption and uptake kinetics and identified molecular species that formed during sorption of carbon dioxide on amine-modified silica. Bicontinuous silicas (AMS-6 and MCM-48) were postsynthetically modified with (3-aminopropyl)triethoxysilane or (3-aminopropyl)methyldiethoxysilane, and amine-modified AMS-6 adsorbed more CO2 than did amine-modified MCM-48. By in situ FTIR spectroscopy, we showed that the amine groups reacted with CO2 and formed ammonium carbamate ion pairs as well as carbamic acids under both dry and moist conditions. The carbamic acid was stabilized by hydrogen bonds, and ammonium carbamate ion pairs formed preferably on sorbents with high densities of amine groups. Under dry conditions, silylpropylcarbamate formed, slowly, by condensing carbamic acid and silanol groups. The ratio of ammonium carbamate ion pairs to silylpropylcarbamate was higher for samples with high amine contents than samples with low amine contents. Bicarbonates or carbonates did not form under dry or moist conditions. The uptake of CO2 was enhanced in the presence of water, which was rationalized by the observed release of additional amine groups under these conditions and related formation of ammonium carbamate ion pairs. Distinct evidence for a fourth and irreversibly formed moiety was observed under sorption of CO2 under dry conditions. Significant amounts of physisorbed, linear CO2 were detected at relatively high partial pressures of CO2, such that they could adsorb only after the reactive amine groups were consumed.

The effects of mesoporous silica nano- (270 nm) and microparticles (2.5 microm) with surface areas above 500 m2/g were evaluated on human monocyte-derived dendritic cells (MDDC). Size- and concentration-dependent effects were seen where the smaller particles and lower concentrations affected MDDC to a minor degree compared to the larger particles and higher concentrations, both in terms of viability, uptake, and immune regulatory markers. Our findings support the further development of mesoporous silica particles in drug and vaccine delivery systems.

Adsorption-mediated CO(2) separation can reduce the cost of carbon capture and storage. The reduction in cost requires adsorbents with high capacities for CO(2) sorption and high CO(2)-over-N(2) selectivity. Amine-modified sorbents are promising candidates for carbon capture. To investigate the details of CO(2) adsorption in such materials, we studied mesocaged (cubic, Pm3n symmetry) silica adsorbents with tethered propylamines using Fourier transform infrared (FTIR) spectroscopy and volumetric uptake experiments. The degree of heterogeneity in these coatings was varied by either cosynthesizing or postsynthetically introducing the propylamine modification. In situ FTIR spectroscopy revealed the presence of both physisorbed and chemisorbed CO(2) in the materials. We present direct molecular evidence for physisorption using FTIR spectroscopy in mesoporous silica sorbents modified with propylamines. Physisorption reduced the CO(2)-over-N(2) selectivity in amine-rich sorbents. Samples with homogeneous coatings showed typical CO(2) adsorption trends and large quantities of IR-observable physisorbed CO(2). The uptake of CO(2) in mesocaged materials with heterogeneous propylamine coatings was higher at high temperatures than at low temperatures. At higher temperatures and low pressures, the postsynthetically modified materials adsorbed more CO(2) than did the extracted ones, even though the surface area after modification was clearly reduced and the coverage of primary amine groups was lower. The principal mode of CO(2) uptake in postsynthetically modified mesoporous silica was chemisorption. The chemisorbed moieties were present mainly as carbamate-ammonium ion pairs, resulting from the quantitative transformation of primary amine groups during CO(2) adsorption as established by NIR spectroscopy. The heterogeneity in the coatings promoted the formation of these ion pairs. The average propylamine-propylamine distance must be small to allow the formation of carbamate-propylammonium ion pairs.

We present a novel conducting polypyrrole-based composite material, obtained by polymerization of pyrrole in the presence of iron(III) chloride on a cellulose substrate derived from the environmentally polluting Cladophora sp. algae. The material, which was doped with chloride ions, was molded into paper sheets and characterized using scanning and transmission electron microscopy, N 2 gas adsorption analysis, cyclic voltammetry, chronoamperometry and conductivity measurements at varying relative humidities. The specific surface area of the composite was found to be 57 m (2)/g and the fibrous structure of the Cladophora cellulose remained intact even after a 50 nm thick layer of polypyrrole had been coated on the cellulose fibers. The composite could be repeatedly used for electrochemically controlled extraction and desorption of chloride and an ion exchanging capacity of 370 C per g of composite was obtained as a result of the high surface area of the cellulose substrate. The influence of the oxidation and reduction potentials on the chloride ion exchange capacity and the nucleation of delocalized positive charges, forming conductive paths in the polypyrrole film, was also investigated. The creation of conductive paths during oxidation followed an effective medium rather than a percolative behavior, indicating that some conduction paths survive the polymer reduction steps. The present high surface area material should be well-suited for use in, e.g., electrochemically controlled ion exchange or separation devices, as well as sensors based on the fact that the material is compact, light, mechanically stable, and moldable into paper sheets.

A novel synthesis route for mesoporous silicates using anionic surfactants has been recently reported. It was advanced that materials synthesized using anionic surfactants and aminosilane groups as co-structure directing agents led to the synthesis of highly ordered, novel mesoporous materials with unprecedented structural properties. Here we present an in-depth high-resolution transmission electron microscopy (HRTEM) investigation on the structural characteristics of these novel mesoporous solids denoted AMS-n (anionic mesoporous silicas). These materials show increased order in comparison with conventional mesoporous structures as a result of the long-range periodicity of structural modulations. Structural defects formed in these materials are investigated using electron diffraction (ED) and Fourier transform (FT) diffractograms. In addition we present a new cubic mesostructure AMS-8 (space group Fd3̄m). These new materials show promising new pore connectivities and morphologies making them ideal for applications ranging from catalysts' supports to gas separation, and from nanodevices to drug delivery.

Although ordered mesoporous silica materials have been studied for almost 20 years, their utilization within life science applications is relatively new and unexplored. An increasing number of researchers are transcending their respective fields in order to bridge the knowledge gap between materials chemistry and biotechnology, and to exploit the potential of mesoporous materials. Their intricate porosity with order in the nanoscale translates into high surface areas above 1000 m(2)/g, high selectivity for the encapsulation of biorelevant molecules as well as controlled surface chemistry. Their uses in pharmaceutics to improve drug formulation, drug bioavailability, mitigate drug toxicity and in cellular targeting, through controlled drug delivery strategies, have been shown. The incorporation of a high concentration of fluorescent and nuclear markers within their pores, whilst retaining good diffusion through their porous matrix, has shown them to be ideal candidates for sensing devices, in immunoassays such as flow cytometry and for their use in novel theranostic applications. This article aims to bring to the forefront some of the most important properties of mesoporous materials, which prove advantageous for their use in nanomedical applications and to highlight some of the potential areas into which the field may now emerge.