The two-level circuit of technological influence of providing of operating properties of hard-tempered large module gears is offered on basis division of tasks of technologist and designer with regulation of complex parameters on each of these stages and subsequent decision of task of choice of optimum value of operating properties.
The subject matter of the research is issues related to the optimization of the technology for reconditioning large-size high precision gear rims of the drives of mining complexes, mine lifting equipment, heavy vehicles; these issues are a perspective trend for reducing the cost of reconditioning and operation of expensive unique equipment. The goal is to ensure intensifying production processes, increasing workloads and speeds, reducing the deterioration of high precision gear rims. The objective is to develop a new technology to optimize reconditioning large high precision gear rims. To achieve this, the following method is suggested -to machine gear rims after they have been surfaced by pre-milling with special hob cutters with a prominence and by final machining the teeth with special cutters equipped with hardmetal inserts that process teeth along the line of engagement, which does not require making full-length cutting teeth and increases the quality of machining, the durability of hardmetal milling cutters. The process of reconditioning of large high precision gear rims is a resource-saving technology, as compared with manufacturing new parts, this technology considerably reduces the cost of materials for manufacturing, decreases a number of process steps, reduces the cost of machining equipment, tools, cutting and measuring instruments. The smooth operation of a gear train can be ensured only at a constant gear ratio but due to manufacturing and operational errors, the gear ratio is not constant at every time, which intensify the deterioration of large high precision gear rims. The following results are obtained. The possibility and practicability of using hob cutters with a prominence (m = 20-28 mm) while rough cutting the worn and reconditioned large gear rims was proved. To obtain the necessary durability of rough milling cutters, it is recommended that the prominence angle be set within 8-10°. The use of hardmetal hob cutters for finishing makes it possible to increase the performance rate by 2 to 3 times as compared to high-speed cutters of other designs and to obtain the necessary quality and precision of manufacturing worn and reconditioned large gear rims. Conclusions. The technology for the optimization of reconditioning large high precision gear rims with the use of special and universal hardmetal single-and double-flute cutters that have both re-sharpened cutting elements and disposable rotary tools was developed and introduced.Keywords: new optimization technology, reconditioning large gear rims, high precision, hob cutters with a protuberance, special cutters, machining tooth along the line of engagement, improving the quality of machining.
Институт теоретической и экспериментальной физики им. А. И. Алиханова Б. Черемушкинская ул., д.25, Москва -117218, Россия Аннотация -Представлены результаты исследования и разработки технологических процессов получения микромеханических элементов (ММЭ) микроэлектромеханических систем (МЭМС) для СВЧ-приборов. Представлено использование процессов обработки кремниевых и стеклянных пластин на различных этапах получения ММЭ МЭМС. Приведены результаты исследования стеклянных пластин с металлизированной поверхностью. I. ВведениеВ СВЧ приборы и устройства может входить весь набор функциональных узлов: передатчики, приемники, средства обработка, синхрогенераторы, источники вторичного электропитания и т.д. Нами проводится разработка структур "кремний на изоляторе", элементов МЭМС, потенциально применимых для СВЧ приборов и устройств. Представляет практическую значимость применение электростатических приводов в качестве микропереключателей СВЧ сигналов. Эти переключатели обладают такими преимуществами, как низкие вносимые потери, высокая добротность, низкая потребляемая мощность, хорошая изоляция на высокой частоте и низкая стоимость. Возможность изготовления электромеханических переключателей на одном кристалле с микроэлектронными компонентами открывает перспективу создания систем с более высокой функциональностью.При изготовлении микромеханической части МЭМС с емкостной системой съема перемещений используются различные материалы. В данной работе приводятся результаты исследований, направленных на получение ММЭ МЭМС, состоящих из кремниевой подвижной части и стеклянного неподвижного основания. В этом случае из-за различий свойств поверхностей кремния и стекла, физикохимических особенностей материалов при воздействии температурного фактора и химических реагентов существуют особенности подготовки и сборки ММЭ. ll. Основная частьПрименяемые технологические процессы при изготовлении ММЭ условно можно разделить на две группы. В первую входят процессы, реализуемые на пластинах стандартного размера -из кремния и/или стекла диаметром 100 мм различной толщины. Во вторую группу входит обработка сформированных и отделенных от пластины элементов подвижной части и неподвижного основания для последующей сборки. В последнем случае используется специально разработанная оснастка для проведения технологических процессов.Проведенные исследования показали, что в процессе изготовлении ММЭ перед термическим окислением, нанесением фоторезиста, анизотропным травлением, стыковкой элементов и в других случаях оптимально использование стандартного двухстадийного процесса жидкостной химической обработки, типичного для микроэлектронного производства ИС с минимальными топологическими размерами элементов более 1 мкм. В этом случае для удаления органических пленок и загрязнений необходимым является использование раствора Каро. Для удаления механических загрязнений эффективно использование перекисно-аммиачного раствора. В случае обработки металлизированных поверхностей используется процесс погружения в раствор диметилформамида. Применительно к стеклян...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.