We demonstrate a colorimetric glucose recognition material consisting of a crystalline colloidal array embedded within a polyacrylamide-poly(ethylene glycol) (PEG) hydrogel, or a polyacrylamide-15-crown-5 hydrogel, with pendent phenylboronic acid groups. We utilize a new molecular recognition motif, in which boronic acid and PEG (or crown ether) functional groups are prepositioned in a photonic crystal hydrogel, such that glucose self-assembles these functional groups into a supramolecular complex. The formation of the complex results in an increase in the hydrogel cross-linking, which for physiologically relevant glucose concentration blue shifts the photonic crystal diffraction. The visually evident diffraction color shifts across the visible spectral region over physiologically important glucose concentration ranges. These materials respond to glucose at physiological ionic strengths and pH values and are selective in their mode of response for glucose over galactose, mannose, and fructose. Thus, we have developed a new recognition motif for glucose that shows promise for the fabrication of noninvasive or minimally invasive in vivo glucose sensing for patients with diabetes mellitus.

We developed a carbohydrate sensing material, which consists of a crystalline colloidal array (CCA) incorporated into a polyacrylamide hydrogel (PCCA) with pendent boronic acid groups. The embedded CCA diffracts visible light, and the PCCA diffraction wavelength reports on the hydrogel volume. This boronic acid PCCA responds to species containing vicinal cis diols such as carbohydrates. This PCCA photonic crystal sensing material responds to glucose in low ionic strength aqueous solutions by swelling and red shifting its diffraction as the glucose concentration increases. The hydrogel swelling results from a Donnan potential due to formation of boronate anion; the boronic acid pK(a) decreases upon glucose binding. This sensing material responds to glucose and other sugars at <50 microM concentrations in low ionic strength solutions.

Strength of structural materials and fibers is usually increased at the expense of strain at failure and toughness. Recent experimental studies have demonstrated improvements in modulus and strength of electrospun polymer nanofibers with reduction of their diameter. Nanofiber toughness has not been analyzed; however, from the classical materials property trade-off, one can expect it to decrease. Here, on the basis of a comprehensive analysis of long (5-10 mm) individual polyacrylonitrile nanofibers, we show that nanofiber toughness also dramatically improves. Reduction of fiber diameter from 2.8 μm to ∼100 nm resulted in simultaneous increases in elastic modulus from 0.36 to 48 GPa, true strength from 15 to 1750 MPa, and toughness from 0.25 to 605 MPa with the largest increases recorded for the ultrafine nanofibers smaller than 250 nm. The observed size effects showed no sign of saturation. Structural investigations and comparisons with mechanical behavior of annealed nanofibers allowed us to attribute ultrahigh ductility (average failure strain stayed over 50%) and toughness to low nanofiber crystallinity resulting from rapid solidification of ultrafine electrospun jets. Demonstrated superior mechanical performance coupled with the unique macro-nano nature of continuous nanofibers makes them readily available for macroscopic materials and composites that can be used in safety-critical applications. The proposed mechanism of simultaneously high strength, modulus, and toughness challenges the prevailing 50 year old paradigm of high-performance polymer fiber development calling for high polymer crystallinity and may have broad implications in fiber science and technology.

The surface of monodisperse silica particles synthesized using the Stober process were coated with a thin layer of polystyrene. Surface charge groups were attached by a grafting polymerization of styrene sulfonate. The resulting highly charged monodisperse silica particles self-assemble into crystalline colloidal arrays (CCA) in deionized water. We polymerized hydroxyethyl methacrylate (HEMA) around the CCA to form a HEMA-polymerized crystalline colloidal array (PCCA). Hydrofluoric acid was utilized to etch out the silica particles to produce a three-dimensional periodic array of voids in the HEMA PCCA. The diffraction from the embedded CCA sensitively monitors the concentration of ethanol in water because the HEMA PCCA shows a large volume dependence on ethanol due to a decreased Flory-Huggins mixing parameter. Between pure water and 40% ethanol the diffraction shifts across the entire visible spectral region. We accurately modeled the dependence of the diffraction wavelength on ethanol concentration using Flory theory. We also fabricated a PCCA (which responds to pH changes in both low and high ionic strength solutions) by utilizing a second polymerization to incorporate carboxyl groups into the HEMA PCCA. We were also able to model the pH dependence of diffraction of the HEMA PCCA by using Flory theory. An unusual feature of the pH response is a hysteresis in response to titration to higher and lower pH. This hysteresis results from the formation of a Donnan potential at high pH which shifts the ionic equilibrium. The kinetics of equilibration is very slow due to the ultralow diffusion constant of protons in the carboxylated PCCA as predicted earlier by the Tanaka group.

We developed a polymerized crystalline colloidal array photonic material that senses metal cations in water at low concentrations (PCCACS). Metal cations such as Cu2+, Co2+, Ni2+, and Zn2+ bind to 8-hydroxyquinoline groups covalently attached to the PCCACS. At low metal concentrations (