While micro-FE simulations have become a standard tool in computational biomechanics, the choice of appropriate material properties is still a relevant topic, typically involving empirical grey value-to-elastic modulus relations. We here derive the voxel-specific volume fractions of mineral, collagen, and water, from tissue-independent bilinear relations between mineral and collagen content in extracellular bone tissue (J. Theor. Biol. 287: 115, 2011), and from the measured X-ray attenuation information quantified in terms of grey values. The aforementioned volume fractions enter a micromechanics representation of bone tissue, as to deliver voxel-specific stiffness tensors. In order to check the relevance of this strategy, we convert a micro Computer Tomograph of a mouse femur into a regular Finite Element mesh, apply forces related to the dead load of a standing mouse, and then compare simulation results based on voxel-specific heterogeneous elastic properties to results based on homogeneous elastic properties related to the spatial average over the solid bone matrix compartment, of the X-ray attenuation coefficients. The element-specific strain energy density illustrates that use of homogeneous elastic properties implies overestimation of the organ stiffness. Moreover, the simulation reveals large tensile normal stresses throughout the femur neck, which may explain the mouse femur neck's trabecular morphology being quite different from the human case, where the femur neck bears compressive forces and bending moments.

No abstract

Driving the field of micro computed tomography toward more quantitative, rather than qualitative, approaches, we here present a new evaluation method, which uses the unique linear relationship between gray values and x-ray attenuation coefficients, together with the energy-dependence of the latter, to identify (i) the average x-ray energy used in the CT device, (ii) the x-ray attenuation coefficients, and (iii), via the x-ray attenuation average rule, the intravoxel composition, i.e., the microporosity, which, amongst others, governs the voxel-specific mechanical properties, such as stiffness and strength. The method is realized for six 3D tricalcium phosphate scaffolds, seeded with pre-osteoblastic cells and differentiated for 3, 6, and 8 weeks, respectively. The corresponding voxel-specific microporosities turn out to increase during the culturing period (resulting in reduced elastic properties, as determined from micromechanical considerations), while the overall macroporosity remains constant. The new methods are expected to further foster the development of a rationally based and computer-aided design of biomaterials and tissue engineering scaffolds.

No abstract

Background Helicopter emergency medical services personnel operating in mountainous terrain are frequently exposed to rapid ascents and provide cardiopulmonary resuscitation (CPR) in the field. The aim of the present trial was to investigate the quality of chest compression only (CCO)‐CPR after acute exposure to altitude under repeatable and standardized conditions. Methods and Results Forty‐eight helicopter emergency medical services personnel were divided into 12 groups of 4 participants; each group was assigned to perform 5 minutes of CCO‐CPR on manikins at 2 of 3 altitudes in a randomized controlled single‐blind crossover design (200, 3000, and 5000 m) in a hypobaric chamber. Physiological parameters were continuously monitored; participants rated their performance and effort on visual analog scales. Generalized estimating equations were performed for variables of CPR quality (depth, rate, recoil, and effective chest compressions) and effects of time, altitude, carryover, altitude sequence, sex, qualification, weight, preacclimatization, and interactions were analyzed. Our trial showed a time‐dependent decrease in chest compression depth ( P =0.036) after 20 minutes at altitude; chest compression depth was below the recommended minimum of 50 mm after 60 to 90 seconds (49 [95% CI, 46–52] mm) of CCO‐CPR. Conclusions This trial showed a time‐dependent decrease in CCO‐CPR quality provided by helicopter emergency medical services personnel during acute exposure to altitude, which was not perceived by the providers. Our findings suggest a reevaluation of the CPR guidelines for providers practicing at altitudes of 3000 m and higher. Mechanical CPR devices could be of help in overcoming CCO‐CPR quality decrease in helicopter emergency medical services missions. Registration URL: https://www.clinicaltrials.gov ; Unique identifier: NCT04138446.