The low-fusing glass application followed by hydrofluoric acid etching and silanization seems to be a promising method for improving the resin bond strength to yttria-stabilized tetragonal zirconia, but the adhesion to this substrate is still a challenge. SUMMARYThe purpose of this study was to evaluate the effect of different surface treatments of yttriastabilized tetragonal zirconia (Y-TZP) on bond strength durability and marginal discrepancies. For adhesion testing, 144 specimens of VITA In-Ceram YZ ceramic for InLab were obtained (5.2533.7534.5 mm) and divided into six groups (n=24) according to the surface treatment: 1) Control (CRTL): untreated; 2) SIL: tribochemical silica coating (CoJet system, 3M/ESPE AG); 3) V1+HF: spray application of low-fusing porcelain glaze (V1, VITA Akzent Spray Glaze) followed by etching with hydrofluoric acid (HF) (one minute); 4) V1+SIL: V1 glazing (VITA Akzent Spray Glaze) followed by tribochemical silica coating; 5) V2+HF: brush application of low-fusing porcelain glaze (VITA Akzent Glaze) plus etching with HF (one minute); and 6) V2+SIL: V2 glazing (VITA Akzent Glaze) plus tribochemical silica coating. After all treatments, the surfaces were silanized for five minutes (ESPE-SIL) and cementation was performed using Panavia F (Kuraray). Half of the specimens in each treatment were tested 24 hours after cementation (dry), with the other half subjected to storage (150 days) and thermocycling (12,0003) (aging), and then a shear test was carried out (1 mm/ min). The micromorphological (digital optical profilometry and scanning electron microscopy) and elemental analyses of the treated surfaces were performed. The inner surfaces of 60 Y-TZP infrastructures were conditioned and marginal fit was evaluated. The statistical analysis revealed that the groups treated via surface glaze application followed by hydrofluoric acid etching and silanization showed the highest bond strength (in dry and aging conditions), but the bond strengths were affected by aging. The highest marginal discrepancies were observed in the groups receiving glaze (117.4 6 29.6 to 105.8 6 12.2 lm) when compared to other groups (55.3 6 8.7 and 55 6 8.5 lm). Low-fusing porcelain glaze + hydrofluoric acid etching changed the morphology of the Y-TZP ceramic and improved the adhesion to the resin cement, but obtaining high and stable bond values to Y-TZP remains challenging. Marginal discrepancies increased with glazing.

This study tested the bond strength of a resin cement to a glass-infiltrated zirconia-alumina ceramic after three conditioning methods and using two test methods (shear-SBS versus microtensile-MTBS). Ceramic blocks for MTBS and ceramic disks for SBS were fabricated.Three surface conditioning (SC) methods were evaluated: (1) 110-μm Al2O3+silanization; (2) Chairside silica coating+silanization; (3) Laboratory silica coating+silanization. Following surface conditioning, the resin cement (Panavia F) was bonded to the conditioned ceramics. Although no statistically significant differences (p=0.1076) were seen between the test methods, results yielded with the different surface conditioning methods showed statistically significant differences (p<0.0001) (SC2=SC3>SC1). As for the interaction between the factors, two-way ANOVA showed that it was not statistically significant (p=0.1443). MTBS test resulted in predominantly mixed failure (85％), but SBS test resulted in exclusively adhesive failure. On the effects of different surface conditioning methods, chairside and laboratory tribochemical silica coating followed by silanization showed higher bond strength results compared to those of aluminum oxide abrasion and silanization, independent of the test method employed.

A high prevalence of dental trauma exists and its effects on function and esthetics deserve the attention of general dentists. The aim of this study was to assess the level of general dental practitioners' (GDPs) knowledge about guidelines for dental avulsion and its prevention using a questionnaire. The 21-item questionnaire was distributed among 264 GDPs and the survey was realized between August-November 2006. The data obtained were statistically analyzed using descriptive analysis and Pearson's Chi-square test to determine associations between knowledge regarding emergency treatment and dentists from public or private dental schools and years of experience. The results showed that the participants exhibited appropriate knowledge concerning procedures in cases of tooth avulsion and its prevention. The number of correct answers was low in relation to recommended treatment at the site of injury. Storage medium, preparation of the alveolus and splint time for receiving the avulsed tooth received a high number of correct answers. One statistically significant association between years of experience and recommended treatment at the site of the injury in the case an avulsed tooth (chi(2) = 9.384, P = 0.009). In conclusion, this survey showed appropriate knowledge of dental avulsion management and its prevention among the surveyed dentists. The findings also showed that communication between dentists and the population is deficient, especially concerning practitioners of high risk and contact sports.

No abstract

Application of a low-pH adhesive resin onto a hydrofluoric acid etched and silanized feldspathic ceramic surface in combination with chemically polymerized resin cement did not deliver favorable results. The use of adhesive resin with high pH could be clinically advised for the photo-, dual-, and chemically polymerized resin cements tested.