A drug dissolution profile is one of the most critical dosage form characteristics with immediate and controlled drug release. Comparing the dissolution profiles of different pharmaceutical products plays a key role before starting the bioequivalence or stability studies. General recommendations for dissolution profile comparison are mentioned by the EMA and FDA guidelines. However, neither the EMA nor the FDA provides unambiguous instructions for comparing the dissolution curves, except for calculating the similarity factor f2. In agreement with the EMA and FDA strategy for comparing the dissolution profiles, this manuscript provides an overview of suitable statistical methods (CI derivation for f2 based on bootstrap, CI derivation for the difference between reference and test samples, Mahalanobis distance, model-dependent approach and maximum deviation method), their procedures and limitations. However, usage of statistical approaches for the above-described methods can be met with difficulties, especially when combined with the requirement of practice for robust and straightforward techniques for data evaluation. Therefore, the bootstrap to derive the CI for f2 or CI derivation for the difference between reference and test samples was selected as the method of choice.

Non-isothermal differential scanning calorimetry (DSC) was used to study the influences of particle size (daver) and heating rate (q+) on the structural relaxation, crystal growth and decomposition kinetics of amorphous indomethacin. The structural relaxation and decomposition processes exhibited daver-independent kinetics, with the q+ dependences based on the apparent activation energies of 342 and 106 kJ·mol−1, respectively. The DSC-measured crystal growth kinetics played a dominant role in the nucleation throughout the total macroscopic amorphous-to-crystalline transformation: the change from the zero-order to the autocatalytic mechanism with increasing q+, the significant alteration of kinetics, with the storage below the glass transition temperature, and the accelerated crystallization due to mechanically induced defects. Whereas slow q+ led to the formation of the thermodynamically stable γ polymorph, fast q+ produced a significant amount of the metastable α polymorph. Mutual correlations between the macroscopic and microscopic crystal growth processes, and between the viscous flow and structural relaxation motions, were discussed based on the values of the corresponding activation energies. Notably, this approach helped us to distinguish between particular crystal growth modes in the case of the powdered indomethacin materials. Ediger’s decoupling parameter was used to quantify the relationship between the viscosity and crystal growth. The link between the cooperativity of structural domains, parameters of the Tool-Narayanaswamy-Moynihan relaxation model and microscopic crystal growth was proposed.

No abstract

Kinetics and the mechanism of total in vitro hydrolyses (i.e. up to the exhaustion of substrate) of acetylcholine and acetylthiocholine by acetylcholinesterase and butyrylcholinesterase were studied in vitro in a batch reactor at 25 ∞C, pH 8 and ionic strength of 0.11 m. Every hydrolysis was monitored by 2Ð3 independent analytical methods. All studied types of enzymatic hydrolyses fulfilled the MichaelisÐMenten reaction scheme with the irreversible second step. A table of obtained average values of rate constants and estimations of initial molar enzyme concentrations, and discussion of the results are presented.

The original Ellman's spectrophotometrical method for cholinesterase activity determination uses 5,5Ј-dithiobis-2-nitrobenzoic acid (DTNB, Ellman's reagent) as a chromogen and records the level of cholinesterase activity as an increase of absorbance at 412 nm. Although this procedure usually poses no problem, exceptions arise when the concentration of DTNB is far higher than the concentration of acetylthiocholine (ATCH). It was found that the ratio of concentrations of DTNB/ATCH is an important parameter for the ATCH hydrolysis course: high excess of DTNB decreases the hydrolysis rate resulting in a lower measured enzyme activity. Our experiments indicate that this influence of DTNB concentration can be explained by the inhibition of ATCH hydrolysis by DTNB.

A simple biosensor, constructed by bulk-modification of carbon ink with manganese dioxide as a mediator and glucose oxidase as a biocomponent was investigated for its ability to 2633 ORDER REPRINTS serve as amperometric detector for glucose in hydrodynamic as well as in flow injection analysis (FIA) mode. The sensor could be operated at a potential of 0.48 V under physiological conditions (0.1 M phosphate buffer, pH 7.5) and exhibited excellent reproducibility and stability. Factors influencing the amperometric response such as injection volume, flow rate and applied working potential were studied in detail. The screen-printed electrode exhibited a linear amperometric increase with the concentration of D-glucose from 2 to 2500 mg L À1 and gave a 3 detection limit of 0.085 mg L À1 . Due to its remarkable stability such a sensor could be operated continuously for more than four weeks or more than 1000 sample injections. No change of signal height could be observed within an operation period of 12 h. The sensor was exploited for FIA-amperometric determination of glucose in beer and wine samples.

It is well known that the hydrodechlorination (HDC) of chlorinated aromatic contaminants in aqueous effluents enables a significant increase in biodegradability. HDC consumes a low quantity of reactants producing corresponding non-chlorinated and much more biodegradable organic compounds. Two commonly used precious metals free Al alloys (Raney Al-Ni and Devarda’s Al-Cu-Zn) were compared in reductive action in an alkaline aqueous solution. Raney Al-Ni alloy was examined as a universal and extremely effective HDC agent in a diluted aqueous NaOH solution. The robustness of Raney Al-Ni activity is illustrated in the case of HDC of polychlorinated aromatic compounds mixture in actual waste water. In contrast, Devarda’s Al-Cu-Zn alloy was approved as much less active for HDC of the tested chlorinated aromatic compounds, but with a surprisingly high selectivity on cleavage of C-Cl bonds in the meta and sometimes the ortho position in chlorinated aniline and sometimes chlorinated phenol structures. The reaction of both tested alloys with chlorinated aromatic compounds in the aqueous NaOH solution is accompanied by dissolution of aluminum. Dissolved Al in the alkaline HDC reaction mixture is very useful for subsequent treatment of HDC products by coagulation and flocculation of Al(OH)3 caused by simple neutralization of the alkaline aqueous phase after the HDC reaction.

No abstract