Mixed ionic-electronic conducting membranes have seen significant progress over the last 25 years as efficient ways to obtain oxygen separation from air and for their integration in chemical production systems where pure oxygen in small amounts is needed. Perovskite materials are the most employed materials for membrane preparation. However, they have poor phase stability and are prone to poisoning when subjected to CO2 and SO2, which limits their industrial application. To solve this, the so-called dual-phase membranes are attracting greater attention. In this review, recent advances on self-supported and supported oxygen membranes and factors that affect the oxygen permeation and membrane stability are presented. Possible ways for further improvements that can be pursued to increase the oxygen permeation rate are also indicated. Lastly, an overview of the most relevant examples of membrane reactors in which oxygen membranes have been integrated are provided.

No abstract

Palladium-based membranes for hydrogen separation have been studied by several research groups during the last 40 years. Much effort has been dedicated to improving the hydrogen flux of these membranes employing different alloys, supports, deposition/production techniques, etc. High flux and cheap membranes, yet stable at different operating conditions are required for their exploitation at industrial scale. The integration of membranes in multifunctional reactors (membrane reactors) poses additional demands on the membranes as interactions at different levels between the catalyst and the membrane surface can occur. Particularly, when employing the membranes in fluidized bed reactors, the selective layer should be resistant to or protected against erosion. In this review we will also describe a novel kind of membranes, the pore-filled type membranes prepared by Pacheco Tanaka and coworkers that represent a possible solution to integrate thin selective membranes into membrane reactors while protecting the selective layer. This work is focused on recent advances on metallic supports, materials used as an intermetallic diffusion layer when metallic supports are used and the most recent advances on Pd-based composite membranes. Particular attention is paid to improvements on sulfur resistance of Pd based membranes, resistance to hydrogen embrittlement and stability at high temperature.

No abstract

Pd-Ag supported membranes have been prepared by coating a ceramic interdiffusion barrier onto a Hastelloy X (0.2 µm media grade) porous support followed by deposition of the hydrogen selective-Ag-5 µm layer by electroless plating. To one of the membranes an additional Pd (4) porous Al 2 O 3-YSZ layer (protective layer with 50 wt% of YSZ) was deposited by dip-coating followed by calcination at 550°C on top of the Pd-Ag layer, and this membrane is referred to as a double-skin membrane. Both membranes were integrated at the same time in a single reactor in order to assess and compare the performance of both membranes under identical conditions. The membranes have first been tested in an empty reactor with pure gases (H 2 and N 2) and afterwards in the presence of a catalyst (rhodium onto promoted alumina) fluidized in the bubbling regime. The membranes immersed in the bubbling bed were tested at 400°C and 500 °C for 115 and 500 hours, respectively. The effect of the protective layer on the permeation properties and stability of the membranes were studied. The double-skinned membraned showed a H 2 permeance of 1.55•10-6 mol m-2 s-1 Pa-1 at 500 °C and 4 bar of pressure difference with an ideal perm-selectivity virtually infinite before incorporation of particles. This selectivity did not decay during the long term test under fluidization with catalyst particles.

Membrane reactors have demonstrated a large potential for the production of hydrogen via reforming of different feedstocks in comparison with other reactor types. However, the long-term performance and stability of the applied membranes are extremely important for the possible industrial exploitation of these reactors. This study investigates the long-term stability of thin-film Pd-Ag membranes supported on porous Al2O3 supports. The stability of five similarly prepared membranes have been investigated for 2650 h, up to 600 °C and in fluidized bed conditions. Results show the importance and the contribution of the sealing of the membranes at temperatures up to 500 °C. At higher temperatures the membranes surface deformation results in pinhole formation and a consequent decrease in selectivity. Stable operation of the membranes in a fluidized bed is observed up to 450 °C, however, at higher temperatures the scouring action of the particles under fluidization causes significant deformation of the palladium surface resulting in a decreased selectivity.

Membrane reactors for hydrogen production can increase both the hydrogen production efficiency at small scale and the electric efficiency in micro-cogeneration systems when coupled with Polymeric Electrolyte Membrane fuel cells. This paper discusses the achievements of three European projects (FERRET, FluidCELL, BIONICO) which investigate the application of the membrane reactor concept to hydrogen production and micro-cogeneration systems using both natural gas and biofuels (biogas and bio-ethanol) as feedstock. The membranes, used to selectively separate hydrogen from the other reaction products (CH4, CO2, H2O, etc.), are of asymmetric type with a thin layer of Pd alloy (<5 μm), and supported on a ceramic porous material to increase their mechanical stability. In FERRET, the flexibility of the membrane reactor under diverse natural gas quality is validated. The reactor is integrated in a micro-CHP system and achieves a net electric efficiency of about 42% (8% points higher than the reference case). In FluidCELL, the use of bio-ethanol as feedstock for micro-cogeneration Polymeric Electrolyte Membrane based system is investigated in off-grid applications and a net electric efficiency around 40% is obtained (6% higher than the reference case). Finally, BIONICO investigates the hydrogen production from biogas. While BIONICO has just started, FERRET and FluidCELL are in their third year and the two prototypes are close to be tested confirming the potentiality of membrane reactor technology at small scale

No abstract