is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible. Abstract Due to their polyphenolic structure lignins bear a number of interesting functional properties, such as antioxidant activity. Natural antioxidants are very much looked for in the aim of protection of light or oxygen sensitive goods and are being used in active packaging. Poly(lactide) (PLA)-lignin films were prepared by twin screw extrusion followed by thermo-compression using two different commercial sources of alkali lignins obtained from gramineous plants. A good dispersion of lignin in the matrix was observed. Mechanical properties of the compounded material were merely diminished and oxygen barrier properties slightly enhanced. The chromatographic study of the lignins revealed that the low molecular weight fraction of both lignins increased during the polymer processing. The migration of low molecular weight compounds in an ethanol/water solution simulating fatty foodstuff was performed and the antioxidant activity of the extract was analysed. It was found that the activity increases with increasing severity of the heat treatment because of the generation of free phenolic monomers during processing. These results open an interesting way for application of lignins as an active compound in packaging materials. Lignins do not impair the mechanical and barrier performance of the polymer and the plastics processing even allows for the generation of active substances.

In the aim of producing fully organic bionanocomposite based on poly(lactide) (PLA), cellulose nanowhiskers (CNW) were grafted by n-octadecyl-isocyanate (CNW-ICN) applying an in situ surface grafting method. The compatibilizing effect of the long aliphatic grafted chain was investigated by thermal, mechanical and permeability analysis of solvent cast nanocomposite films. The grafted CNW-ICN could be successfully dispersed in the polymer matrix. The gained compatibility brought about a nucleating effect, decreasing the half time of isothermal crystallization from 25 min for the neat PLA to 8.4 min for the nanocomposite including 2.5 wt% CNW-ICN, e.g., tensile strength was improved by 10 MPa for the same 2.5 wt% CNW-ICN/PLA composite. Mechanical reinforcement was also effective in the rubbery state of PLA and increased the tensile modulus of the rubbery plateau providing thereby thermal resistance to the polymer. Oxygen barrier properties did not change significantly upon the inclusion of CNW-ICN, even when the quantity of CNW-ICN was increased to 15 wt%. More interestingly, the water vapour permeability of the CNW-ICN nanocomposite was always lower than the one of ungrafted CNW composites, which led to the conclusion that the hydrophobic surface graft and improved compatibility could counteract the effect of inclusion of hydrophilic structures in the matrix on water vapour transport. In conclusion, the surface grafting of CNW with isocyanates might be an easy and versatile tool for designing fully organic bionanocomposites with tailored properties

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible. AbstractThe thermo-oxidative degradation of polylactide (PLA) films was studied between 70 and 150°C. It was shown that the oxidative degradation of PLA leads to a random chain scission responsible for a reduction of the molar mass. These molar mass changes affect Tg and the degree of crystalllinity, and it was found that Tg decreases according to the Fox-Flory theory whereas the degree of crystalllinity increases due to a chemicrystallization process. A correlation between molar mass and strain at break during oxidation has been established:PLA displays a brittle behaviour when M n falls below 40 kg.mol -1 in agreement with relationships linking the critical value for embrittlement with the molar mass between entanglements.

Poly(lactic acid) is one of the most promising biobased and biodegradable polymers for food packaging, an application which requires good mechanical and barrier properties. In order to improve the mechanical properties, in particular the flexibility, PLA plasticization is required. However, plasticization induces generally a decrease in the barrier properties. Acetyl tributyl citrate (ATBC) and poly(ethylene glycol) 300 (PEG), highly recommended as plasticizers for PLA, were added up to 17 wt% in P(D,L)LA. In the case of PEG, a phase separation was observed for plasticizer contents higher than 5 wt%. Contrary to PEG, the T g decrease due to ATBC addition, modelled with Fox's law, and the absence of phase separation, up to 17 wt% of plasticizer, confirm the miscibility of PLA and ATBC. Contents equal or higher than 13 wt% of ATBC yielded a substantial improvement of the elongation at break, becoming higher than 300%. The effect of PLA plasticization on the barrier properties was assessed by different molecules, with increasing interaction with the formulated material, such as helium, an inert gas, and oxygen and water vapour. In comparison to the neat sample, barrier properties against helium were maintained when PLA was plasticized with up to 17 wt% of ATBC. The oxygen permeability coefficient and the water vapour transmission rate doubled for mixtures with 17 wt% ATBC in PLA, but increased five-fold in the PEG plasticized samples. This result is most likely caused by increased solubility of oxygen and water in the PEG phase due to their mutual miscibility. To conclude, ATBC increases efficiently the elongation at break of PLA while maintaining the permeability coefficient of helium and keeping the barrier properties against oxygen and water vapour in the same order of magnitude.

properties of poly(lactic acid) and its morphological changes induced by aroma compound sorption. Polymer International, Wiley, 2010Wiley, , 59 (6), pp.818-826. 10.1002Wiley, /pi.2793 Barrier properties of poly(lactic acid) and its morphological changes induced by aroma compound sorption Gael Colomines, a Violette Ducruet, b Cécile Courgneau, b Alain Guinault a and Sandra Domenek b * The barrier properties of poly(lactic acid) (PLA) play a key role in food packaging applications. For their optimization, the influence of crystallinity on the barrier properties of PLA and the interaction of PLA with the aroma compound ethyl acetate were investigated. PLA film samples with various crystallinities were fabricated by flat die extrusion and thermocompression and compared to PLA Biophan  . The degree of crystallinity had no effect on the oxygen permeability. However, an increase of crystallinity caused a decrease in ethyl acetate sorption. The sorption isotherm of ethyl acetate obtained using microgravimetry showed a steep increase with increasing aroma activity, a form which is consistent with a plasticization effect. This behaviour was verified using differential scanning calorimetry and dynamic mechanical analysis. Sorption caused a marked decrease in the glass transition temperature well below room temperature to approximately 0• C. Furthermore, PLA underwent a solvent-induced crystallization when equilibrated in ethyl acetate atmosphere at an activity of 0.5. The results obtained show the importance of considering possible interactions between polymer and foodstuff during the optimization step of polymeric materials for food packaging applications.