A giant carbonate field offshore Abu Dhabi is being redeveloped using extended-reach-horizontal-laterals up to 20,000 ft with open hole un-cemented liner, drilled from artificial islands. Long horizontal wells provide significant profitability in unit development cost; however it is critical to ensure effective stimulation of the complete lateral to maximize reservoir recovery. Earlier, SPE171800 introduced an innovative liner design for long open hole horizontal completions, namely Limited-Entry Liner (LEL) that enables high rate aggressive stimulation by bullheading technique. This paper will present the field stimulation results of more than five LEL laterals ranging several-kilometers in open hole completions, demonstrating the impact of LEL stimulations in accelerating production and maximizing reservoir recovery. Several LEL horizontal wells were completed in low-permeability rock to enable high rate bullhead matrix stimulation. ExxonMobil proprietary software is used to design fit-for-purpose LEL that enables acid injection conformance along the lateral and at the same time creates deep-wormholes by high-velocity acid-jets through 3-mm/4-mm holes in liner base-pipe distributed non-uniformly along the lateral, compartmentalized with oil/water-swellable-packers. The execution of the stimulation campaign was made possible through the use of modularized-equipment packages installed on an ADNOC-vessel, utilizing a unique mechanism that locks the package components to frames installed to the vessel-deck. The stimulation package consists of 6×2000HHP pumps delivering up to 60bpm at 10,000psi. The liquid-additive system, 140bbl vertical mixing tank and more than 190,000gallon raw-acid storage tanks are fully automated to enable acid mixing and pumping on the fly at the desired rates, concentrations and recipes. In order to demonstrate the effectiveness of acid placement and effective stimulation across the entire lateral, real-time Fiber-Optic surveillance techniques (DTS-DAS) were utilized. The recorded thermal and acoustic profiles provided a qualitative and quantitative measurement of the effectiveness of the mechanical diversion delivered by the LEL design. These data will help in corroborating and fine-tuning the model used in lower completion design of maximum reservoir contact wells in future field development. Along with well performance and real-time surveillance, production/injection logging data demonstrates effective stimulation of the entire lateral. This paper presents field performance results from successful bullhead stimulation of extended reach horizontal well completed with LEL in low-permeability-reservoir. This paper also presents our first application of fiber-optic-DTS-DAS real-time-surveillance during stimulation and post-stimulation water injection. Advanced surveillance data demonstrated the success and effectiveness of the LEL completion and stimulation in extended-reach long horizontal open hole laterals.
Earlier, SPE Technical Paper 193036 introduced the development, testing, qualification and deployment of plugged liner technology in Extended Reach Drilling (ERD) field re-development from artificial islands of a giant offshore field in the United Arab Emirates (UAE). This paper will highlight the excellent well performance of the two pilot wells and other island wells with this technology deployment and the significant impact of this technology on initial production rates as well as reservoir recovery. Plugged LEL technology utilizes Dissolvable Plugged Nozzle Assemblies (DPNA) for deployment with Limited-Entry-Liner lower completions combined with Remote Close Shoes (RCS). The technology results in about 5 days of rig-time saving in well displacement process in extremely long laterals, switching from the non-aqueous reservoir drilling fluid to an aqueous completion brine, by eliminating the use of a dedicated liner displacement string. Two pilot wells with extra-long horizontal laterals in the very low permeability region were completed with plugged LEL utilizing (1) 169 DPNA 4-mm in 28 zones isolated by swell-packers and (2) 183 DPNA 4-mm in 24 zones isolated by swell-packers. The distribution and location of the DPNA holes along the liner are designed in-house with ExxonMobil proprietary software. After successful deployment of the plugged liner in two pilot wells which resulted in significant CAPEX reduction upfront through reduced duration for well construction, the well performance was monitored closely in order to assess the success of the technology application in terms of production and reservoir objective. The production rates from both pilot wells exceeded the expected production rates. Apart from total production rate, the critical component of this technology was to ensure all the dissolvable nozzles that plug the liner have dissolved across the lateral enabling lateral conformance which is key to initial production rate and reservoir recovery. Thus, production logging tool (PLT) was performed and the results indicated that the entire extended production lateral is contributing to flow. Apart from well construction cost savings, this technology also enables enhanced wellbore cleaning and improved filter-cake breaker placement. These enhancements resulted in improved well performance than expected and lateral conformance which maximizes reservoir recovery from horizontal wells. After the success of the first two pilot wells, field-wide deployment of the plugged liner was initiated and several wells have been completed with this technology. This paper will demonstrate the success of the first global deployment of a novel lower completion technology – plugged nozzles LEL - to maximize production and recovery in ERD wells with very long laterals. Value and impact of this technology will be presented in terms of well performance, reservoir recovery in addition to previously highlighted well construction cost savings.
One of the most giant offshore multi-reservoir oil fields in the world has been developed using vertical, deviated and short horizontal wells drilled off-shore from wellhead platform towers. Towards the concept of cost optimization, further redevelopment of the oil field was planned using extended-reach long horizontal wells with throws greater than 18,000 ft and measured depths greater than 25,000 ft with some wells exceeding 35,000 ft, from artificial built islands by reducing the number of wells required to drain the reservoir with improving recovery. In order to enable transition to such concept, new well design strategic concepts were required to come up with the robust well completion design (both upper and lower completions) that is expected to be fit-for-purpose for 30+ years – well life time. Lots of uncertainties and challenges are faced in order to get to the goal of understanding different reservoirs behaviors such as, for better reservoirs development relying on dynamic reservoir models combined with actual geological, petrophysical, seismic and production data. Each piece of information yielded a certain potential that led to a certain completion design based on available data and expectations. This paper will discuss the upper and lower completion designs, execution and performance from production engineering perspective to maximize productivity for the whole life cycle of this long horizontal wells. The extended lateral length in these wells warrants innovative designs in upper and lower completions as traditional completion designs no longer valid in addressing the challenges in these wells. The key well design and planning process involves designing the upper completion – tubing, gas lift system, downhole gauge and lower completion liner – Pre-perforated liner (PPL), Limited-entry Liner (LEL) or Inflow Control Devices (ICD) with annular isolation with packers, efficient initial start-up and clean up strategy, regular monitoring well performance and surveillance (e.g. downhole pressure monitoring, PLTs, fluid sample analysis etc.). The paper will also address the challenges in long horizontal wells such as accessibility, production/injection conformance and effective stimulation of the laterals.
Objectives/Scope A new vision with new techniques of wells’ upper and lower completions have been applied successfully throughout a giant offshore multi-reservoir oilfield. Wells with long to very-long laterals have been completed successfully following a systematic strategy based applications and showed tremendous success. This paper will present the various techniques used completing wells in different reservoirs considering well-integrity and HSE regulations in order to achieve the maximum wells’ deliverability’s at their lowest costs throughout the well life. Many challenges were faced and overcame in order to reach the optimum completion that suits each well. A complete journey from reservoir simulation to well and network models, well performance to reservoir management studies, from geological models and interpretation to geo-science and seismic inputs, in addition to actual production data, all helped to achieve the over-all target. From the phase of design to the phase of implementation and beyond to the production phase, each piece of information yielded a certain potential that led to a certain completion design based on available data and expectations. Methods, Procedures, Process This paper will discuss the new innovative upper and lower completion designs’ strategies along with the execution and performance from production engineering perspective in order to reach the maximum productivity for the life cycle from these long horizontal wells at the lowest possible cost. The extended lateral length in these wells warrants innovative designs in upper and lower completions, as the traditional completion designs no longer suite to address the challenges in these wells. The key well design and planning process involves designing the upper completion including suitable tubing size with the most effective and durable gas-lift system, and lower completion liner designs for different wells’ cases. Efficient initial strategies to start-up wells including some protocols with well-performance monitoring and reservoir surveillance. The paper will also address and discuss the challenges in long horizontal wells such as accessibility, production/injection conformance, and effective stimulations of these laterals. Results, Observations, Conclusions This paper will discuss and show many examples of the completed wells with different types of completions and a comparison of their performances after initial startup and during the back-flow period in addition to the extended performance during normal flowing conditions. Some LEL wells were logged and stimulated showing excellent results; these results will be shared in the paper. It is concluded that the LEL completion proved itself to be the future for lower completion to be widely used in the field. Novel/Additive Information The novelty of such new applications were that they were designed in-house and applied on considerable number of long lateral wells showing excellent results that is changing the completion future strategy in the field and may be in the region or even worldwide.
A giant oil field offshore has been developed to date using vertical and then horizontal wells drilled off-shore from wellhead platform towers. In order to reduce costs reducing the number of wells required to drain the reservoir with improving recovery, further development of the field was planned using extended-reach long horizontal wells with throws greater than 18,000 ft and measured depths greater than 25,000 ft with some wells exceeding 35,000 ft. This paper will discuss how to reach an integrated robust completion design methodology to maximize performance of these long horizontal wells. The methodology considers a combination of two essential designs; Lower completion design and Stimulation design. While the key objective of lower completion and stimulation designs has been to connect wells to reservoirs at their best performances with the most effective and economical way, productivity/injectivity from every foot of these long laterals as well as long term performance are the keys to successful well design and reservoir development strategy. The design methodology incorporates several constraints from reservoir such as heterogeneities in permeability, pressure and porosity, and uncertainties in those properties prediction including presence of faults/thief zones. The design methodology also incorporates the objective to be able to perform well surveillance, such as PLTs, as well as manageable installation of lower completion. The paper will give examples of application of this methodology in designing a10,000+ ft long limited-entry liner which facilitates bullhead high pressure – high rate stimulation – high acid concentration in order to place acid across the entire lateral and maximize stimulation effectiveness of every foot of the lateral. The paper will also discuss actual well performances of available long lateral wells along with lessons learned.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.