The study was focused on the performance of rutile addition in the glaze for antibacterial application. Rutile powder in micro size (<5µm) (at different composition 5 wt%, 7 wt%, 9 wt%, 10 wt% and 15 wt%) were added in the glaze. Glazing was performed by dipping method for 10 seconds. Glazed tile was then sintered at 1200°C for 1 hour. Characterizations used to observe the properties of produced tiles were physical observation, scanning electron microscopy (SEM) and X-ray diffraction (XRD). Optimum sample was undergone an antibacterial test towards E.coli.
Titania (TiO2) is one of a common and favorable material use in the manufacturing industry due to its uniqueness and functional performances to human and environment. The study was focused on the performance of glaze added TiO2 (anatase phase) in the application of porcelain tiles. Anatase powder in micro size was used (varies at 5 wt%, 10 wt % and 15 wt%) to observe their performance as antibacterial materials. The anatase powders were mix into the glaze composition and apply to the porcelain tile through dip coating. The viscosity of each composition was observed to study their effect. Characterization used to observe the properties of anatase mixed glazed porcelain tile were X-ray diffraction (XRD), Scanning electron microscopy (SEM) and antibacterial test. The results shown that higher composition of anatase powder, viscosity of the mixed glaze is higher and a rougher surface of glazed tiles was formed. XRD result shows that the higher the composition is more the intensity of TiO2 on the glaze coating surface, supported by SEM results. Antibacterial testing towards E.Coli was observed by counting the colonies of bacterial growth in 0 hr, 2 hrs, 4 hrs and 8hrs. The antibacterial properties increase when the composition of anatase increases.
Lime sludge (LS) is a solid waste from lime making industry and normally disposed in landfill or recycled. LS has been studied as one of the raw materials in various ceramic productions such as bricks, ceramic tiles and glass-ceramics. In this study, LS was utilized in the preparation of bioactive glass using the 45S5 bioactive glass. The 45S5 bioactive glass contains SiO2 (45 wt.%), Na2O (24.5 wt.%), CaO (24.5 wt.%) and P2O5 (6 wt.%). It has the ability to bond with soft tissue and promote bone growth. The LS was combined with bioactive glass as a potential replacement of calcium carbonate (CaCO3). The ratio between LS:CaO was varied (0:100, 25:75, 50:50, 75:25 and 100:0) to study the effect of LS weight percentage on the bioctive glass. The preparations of bioactive glasses involved batching, mixing, melting at 1400 °C, water quench and milling. LS was characterized using X-ray diffraction (XRD), while the fabricated glasses were characterized using particle size analyzer, XRD and scanning electron microscopy (SEM). The XRD results proved that the phase and chemical composition of bioactive glass were not affected by the addition of LS. The XRD and SEM results indicated that the addition of lime sludge in bioactive glass was effective to promote the formation of hydroxyapatite (HA) layer.
CaCu3Ti4O12 (CCTO) is an electroceramic material with complex cubic perovskite-like oxide. It possessed a giant dielectric constant of about 105 over a wide temperature range (100-600 K). In this work, CCTO was synthesized through solid state method. The effect of different heating rate during sintering process was studied. The raw materials - CaCO3, CuO and TiO2 were wet ball milled for 24 hours and calcined at 900 °C for 10 hours. Then the calcined powder was pressed into pellet shape at 300 MPa. Sintering was done at 1040 °C for 12 hours with different heating rates: 3, 5 and 10 °C/min. The phase formation and surface morphology was investigated by X-Ray Diffraction (XRD) and Field Emission Scanning Electron Microscope (FESEM), respectively. The density was measured by Archimedes Principle. XRD pattern proves the CCTO single phase formation for the calcined powder and sintered pellet. The SEM images show the different grain size for different heating rate. The density of the pellet was found to be reduced when faster sintering heating rate was used.
Porous cordierite is among the special porous ceramic due to its extensive properties. In this research, porous cordierite was fabricated through gelcasting method. A mixture of raw materials (SiO2, Al2O3 and MgO) was melted at 1550 °C followed by quenching in water to produce a glass. Then the formed glass powder were milled for 1, 3, 5, 7 and 9 hours to obtain various particle sizes of cordierite powder. Cordierite powder produced was then used to prepare 3-D porous cordierite ceramic using gelcasting method. The cordierite pellets were characterized. Surface morphology was analysed via Scanning Electron Microscope (SEM) to observe the pore structure of porous cordierite formed from powder with various particle sizes.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.