We report the fabrication of a photosensor based on as-grown single crystal monolayers of MoS2 synthesized by chemical vapor deposition (CVD). The measurements were performed using Au/Ti leads in a two terminal configuration on CVD-grown MoS2 on a SiO2/Si substrate. The device was operated in air at room temperature at low bias voltages ranging from −2 V to 2 V and its sensing capabilities were tested for two different excitation wavelengths (514.5 nm and 488 nm). The responsivity reached 1.1 mA W−1 when excited with a 514.5 nm laser at a bias of 1.5 V. This responsivity is one order of magnitude larger than that reported from photo devices fabricated using CVD-grown multilayered WS2. A rectifying-effect was observed for the optically excited current, which was four times larger in the direct polarization bias when compared to the reverse bias photocurrent. Such rectifying behavior can be attributed to the asymmetric electrode placement on the triangular MoS2 monocrystal. It is envisioned that these components could eventually be used as efficient and low cost photosensors based on CVD-grown transition metal dichalcogenide monolayers.
This work shows evidence of conventional liquid and polymer molecules doping macroscopic yarns made up of carbon nanotubes (CNT), an effect that is exploited to monitor polymer flow and thermoset curing during fabrication of a structural composite by vacuum infusion. The sensing mechanism is based on adsorption of liquid/polymer molecules after infiltration into the porous fibers. These molecules act as dopants that produce large changes in longitudinal fiber resistance, closely related to the low density of carriers near the Fermi level of bulk samples of CNT fibers, reminiscent of their low‐dimensional constituents. A 25% decrease in fiber resistance upon exposure to electron–donor radicals formed during epoxy vinyl ester polymerization is shown as an example. At later stages of curing the matrix undergoes shrinkage and applies a compressive stress to the fibers. The resulting sharp increase in electrical resistance provides a mechanism for detection of the matrix gel point. The kinetics of resistance change during polymer ingress are related to established models for macromolecular adsorption, thus also enabling prediction of polymer flow. This is demonstrated for vacuum infusion of a 150 cm2 glass fiber laminate composite, with the CNT fiber yarns giving accurate prediction of macroscopic resin flow according to Darcy's law.
Metamaterials are artificial materials that derive their unusual properties from their periodic architecture. Some metamaterials can deform their internal structure to switch between different properties. However, the precise control of these deformations remains a challenge, as these structures often exhibit non-linear mechanical behavior. We introduce a computational and experimental strategy to explore the folding behavior of a range of 3D prismatic building blocks that exhibit controllable multifunctionality. By applying local actuation patterns, we are able to explore and visualize their complex mechanical behavior. We find a vast and discrete set of mechanically stable configurations, that arise from local minima in their elastic energy. Additionally these building blocks can be assembled into metamaterials that exhibit similar behavior. The mechanical principles on which the multistable behavior is based are scale-independent, making our designs candidates for e.g., reconfigurable acoustic wave guides, microelectronic mechanical systems and energy storage systems.
Microwave optomechanical circuits have been demonstrated in the past years to be extremely powerfool tools for both, exploring fundamental physics of macroscopic mechanical oscillators as well as being promising candidates for novel on-chip quantum limited microwave devices. In most experiments so far, the mechanical oscillator is either used as a passive device element and its displacement is detected using the superconducting cavity or manipulated by intracavity fields. Here, we explore the possibility to directly and parametrically manipulate the mechanical nanobeam resonator of a cavity electromechanical system, which provides additional functionality to the toolbox of microwave optomechanical devices. In addition to using the cavity as an interferometer to detect parametrically modulated mechanical displacement and squeezed thermomechanical motion, we demonstrate that parametric modulation of the nanobeam resonance frequency can realize a phase-sensitive parametric amplifier for intracavity microwave photons. In contrast to many other microwave amplification schemes using electromechanical circuits, the presented technique allows for simultaneous cooling of the mechanical element, which potentially enables this type of optomechanical microwave amplifier to be quantum-limited. INTRODUCTIONSuperconducting microwave circuits have been demonstrated to be extremely powerful tools for the fields of quantum information processing 1-3 , circuit quantum electrodynamics 4-8 , astrophysical detector technologies 9 and microwave optomechanics 10-12 . In the latter, microwave fields in superconducting cavities are parametrically coupled to mechanical elements such as suspended capacitor drumheads or metallized nanobeams, enabling high-precision detection and manipulation of mechanical motion. Milestones achieved in the field include sideband-cooling of mechanical oscillators to the quantum ground state 11 , strong coupling between photons and phonons 13 , the generation of non-Gaussian states of motion [14][15][16] or the entanglement between two mechanial oscillators 17 .Recently, there are increasing efforts taken towards building passive and active quantum limited microwave elements for quantum technologies based on microwave optomechanical circuits, connecting the fields of microwave optomechanics, circuit quantum electrodynamics and quantum information science 18-20 . Among the most important developments into this direction are the demonstration of microwave amplification by blue sideband driving in simple optomechanical circuits 21 , and the realization of directional microwave amplifiers 22 as well as microwave circulators 23,24 in more complex multimode systems 25 .Recent theoretical work 26-28 on optomechanical systems with a parametrically driven mechanical oscillator proposed the use of mechanical parametric driving to enable parametric amplification with enhanced bandwidth and reduced added noise, compared to the case of a optomechanical amplifier using a blue-sideband drive 26 . Furthermore, the authors pre...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.