Quartz Crystal Microbalance (QCM) sensor responds measurement can be done in three different methods. One method which gives a rich information is the impedance measurement of the QCM sensor using a phase gain measurement. In this configuration, the QCM sensor was placed in a configuration where the sensor was injected with a sinusoidal signal. Signal gain and phase difference between the signal before and after the QCM sensor was measured and compared. An integrated circuit which able to measure the gain and phase difference is available in a low cost and small footprint. In other hand, the high-performance digital oscilloscope is also available in the market with reasonably priced. In this experiment, we comparing the use of the AD8302, gain and phase detector circuit, and Picoscope 5244B. Picoscope 5244B is a high-performance Digital Storage Oscilloscope (DSO). The result showed that the AD8302 gave an easy and direct results of the gain and phase value. The output can directly processed using a microcontroller which allow for the development of a gain and phase detection system. In other hand, the DSO provided a true signal comparison between the input signal and output signal, but it required a complex processing.
Emissions from burning biomass have become a problem in Indonesia. As found on the Indonesian island of Lombok, agricultural waste is burned for traditional industrial activities. On the other hand, biomass burning emissions contain many PMs (particulates) in different size distributions recognized to have a significant correlation to health impact. This study is conducted to predict the impact of the PM exposure on blood using a ANN (artificial neural network) model as well as a histological examination. The relationship between both methods is determined to estimate the impact of biomass burning emissions on the blood. This study used male mice as the experimental animals exposed to PM emissions (PM 0.1 , PM 2.5 , and PM 10 ) produced from the burning of various biomass (rice straw, rice husks, corn cobs, corn stalks, and tobacco) taken from Lombok Island. The sample exposure was conducted in a chamber for 100 s for ten sequence days. The blood samples were observed using a microscope with the 400 x magnification. The cell deformation was examined histologically by calculating the normal and abnormal cells. The percentage of the erythrocyte deformation was assessed using a fixed back and forth propagation ANN. The result shows that the biomass burning PM emissions have a significant impact on the erythrocyte deformation depending on the type of biomass and the particulate matter emissions. The ANN model confirms the erythrocyte deformation data obtained by the histological examination method.
Most of existing adaptive control schemes are designed to minimize error between plant state and goal state despite the fact that executing actions that are predicted to result in smaller errors only can mislead to non-goal states. We develop an adaptive control scheme that involves manipulating a controller of a general type to improve its performance as measured by an evaluation function. The developed method is closely related to a theory of Reinforcement Learning (RL) but imposes a practical assumption made for faster learning. We assume that a value function of RL can be approximated by a function of Euclidean distance from a goal state and an action executed at the state. And, we propose to use it for the gradient search as an evaluation function. Simulation results provided through application of the proposed scheme to a pole-balancing problem using a linear state feedback controller and fuzzy controller verify the scheme’s efficacy
Power quality becomes a severe problem due to the increasing use of nonlinear electrical loads, complex electric power systems on smart grids, inverters in renewable power plants, and electronic control equipment. Power quality problems include variations in voltage or current such as sag, swell, flicker, spike, overvoltage, undervoltage, interruption, transient, harmonics, and frequency fluctuations. Research on power quality disturbances mostly applies signal processing and transformation methods such as Fast Fourier transform, S-transform, and Wavelet. In this paper, we use empirical mode decomposition methods and statistical parameters to analyze power quality disturbance signals. It gives more detailed characteristics of power quality disturbances. We conducted a six-step analysis to get a percentage of each power quality disturbance signal. The developed method provides a preliminary description of the power quality characteristics from the percentage values of RMS, range, and energy levels at the first IMF. The positive percentage indicates the existence of power quality disturbances contains flicker and swell, while negative indicates contain harmonics, sag, and transient.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.