Amorphous Silicon type solar panels, which had a bad reputation in the past, are now considered very reliable, with several significant advantages over Mono Crystalline and Polycrystalline solar panels. Research on the effectiveness of the capture power of Amorphous Silicon compared to Silicon Crystalline solar panels types is still not much done.The purpose of this study was to explain the effect of solar radiation on the capture power of polycrystalline and amorphous solar panels.This research method includes solar panel installation, measurement of solar radiation, measurement of the resulting current and voltage, data analysis, discussion, and conclusions. The independent variables of the study were the resulting current and voltage, and the type of solar panels (Polycrystalline and Amorphous). The dependent variable of this research are actual power and efficiency.The results showed that the greater the solar radiation, the higher the actual power and efficiency produced by the solar panels. Polycrystalline type solar panels are capable of producing higher average actual power and average efficiency, namely 86.83 W and 11.92%, compared to amorphous solar panels, namely 43.88 W and 6.01%. Keywords: Monocrystalline, Polycrystalline, Normalized Power Output Efficiency, Performance Ratio
Saat ini teknologi panel surya menjadi peralatan pengkorversi energi listrik yang banyak digunakan untuk berbagai aplikasi. Panel surya mampu mengubah sinar matahari menjadi energi listrik. Energi listrik tersebut selanjutnya dapat disimpan oleh baterai. Pada penelitian ini energi yang disimpan di dalam baterai akan digunakan untuk menggerakkan motor BLDC pada electric scooter. Tujuan dari penelitian ini yaitu untuk membandingkan unjuk kerja jenis panel surya terhadap pengisian daya listrik di electric scooter. Metode penelitian dengan pengujian langsung dari panel surya jenis thin film amorphous dan polycrystalline pada electric scooter. Alat monitoring sistem pengisian baterai berbasis arduino, dirancang untuk mengukur tegangan, arus, daya, arus pengisian, dan persentase baterai. Sedangkan tingkat radiasi matahari diukur dengan solar power meter. Hasil dari penelitian ini berupa electric scooter berbasis panel surya, alat monitoring sistem pengisian baterai. Tingkat radiasi matahari maksimum pada jam 12.00 WIB sebesar 887,4 W/m2 diperoleh bahwa panel surya Polycrystalline menghasilkan daya 11,87 Watt. Nilai ini lebih besar dibandingkan dengan jenis panel surya Thin Film Amorphous yang hanya mampu menghasilkan 10,56 Watt. Kesimpulan dari penelitian ini adalah panel surya jenis Polycrystalline lebih efisien digunakan dari pada panel surya jenis thin film amorphous. Namun secara estetika panel surya thin film amorphous lebih sesuai dengan desain electric scooter yang dirancang.
Lokasi TPQ-Al Murtadho terletak di RW 01, Wonokoyo, Kedungkandang, Kota Malang. Bangunan semi permanen ini didirikan secara swadaya oleh warga setempat. Selain berfungsi sebagai taman pendidikan Al-Quran (TPQ), bangunan ini juga dimanfaatkan untuk tempat musyawarah warga. Sistem penerangan yang murah dan mudah sangat relevan untuk diterapkan pada bangunan tersebut. Oleh karena itu dalam PkM ini dilakukan pelatihan singkat dan pemasangan sistem penerangan bertenaga surya (home solar system). Kegiatan yang dilakukan bersama pemuda karang taruna ini berlangsung selama dua hari. Pelatihan berupa presentasi mengenai listrik tenagasurya, yang dilanjutkan dengan perakitan dan pemasangan instalasi panel surya di TPQ Al-Murtadho. Hasil PkM adalah paket listrik tenaga surya yang terdiri dari : 1 unit panel surya; 1 unit solar charger controller; 1 unit baterai; 3 lampu LED dan peralatan aksesoris. Panel surya yang digunakan adalah 100 WP (Watt Peak) artinya daya maksimum yang mampu dibangkitkan oleh panel surya dalam 1 jam adalah 100 Watt. Jika sinar matahari dalam kondisi normal (cerah) diasumsikan 5 jam, maka panel surya mampu menghasilkan listrik sebesar 500 Wattjam. Sehingga dengan energi tersebut akan mampu untuk menyalakan lampu dengan daya 9 Watt pada 3 titik selama 9-10 jam.
Titanium Grade 2 is a type of material that is often used in industry, especially in materials for biomedical implants. Titanium Grade 2 has a good stiffness to weight ratio, is corrosion resistant and has good biocompatibility in the body. However, it has a low thermal conductivity, so it is necessary to choose the right machining parameter to produce a good surface roughness value. This study aims to determine the characteristics of Titanium Grade 2, namely the surface roughness of the results of lathe machining. The research design used the Taguchi L9 method, with 2 factors and 3 levels. The machining parameters used are spindle rotation 500; 700; 900 rpm and feed speed 25; 50; 75mm/min. The response variable studied was surface roughness. The milling process is carried out using a Maximat V13 lathe. Surface roughness was measured using a Mitutoyo surface roughess tester. Data analysis used ANOVA analysis. The results showed that there was an effect of variations in machining parameters on the surface roughness response. The spindle rotation variable has a p-value of 0.039 and the feeding motion variable has a p-value of 0.025. This shows that the two independent variables have a significant effect on the surface roughness response. The lowest surface roughness can be achieved by setting the spindle rotation at 700 rpm and the feed speed at 25 mm/min.
Proses drilling merupakan proses pemesinan yang paling banyak digunakan di industri otomotif dan manufaktur. Kinerja proses drilling pada material Komposit KFRP bisa diukur dengan karakteristik kualitas seperti kekasaran permukaan, burr height, kebulatan, konsumsi daya, gaya tekan dan delaminasi. Penelitian ini bertujuan untuk mengetahui pengaruh variasi variabel bebas sudut ujung pahat dan kecepatan makan terhadap variabel respon kebulatan. Rancangan percobaan menggunakan metode full faktorial yang berupa orthogonal array L9 dengan replikasi sebanyak dua kali. Variabel bebas yang divariasikan adalah sudut ujung pahat (100°, 118°, 140°) dan kecepatan makan (50 mm/menit, 115 mm/menit dan 180 mm/menit). Variabel respon yang diamati adalah kebulatan. Proses drilling dilakukan menggunakan mesin CNC Milling. Pahat yang digunakan adalah twist drill HSS Nachi diameter 10 mm. ANOVA digunakan untuk mengetahui variabel-variabel bebas yang memiliki pengaruh signifikan terhadap variabel respon yang diamati. Hasil penelitian menunjukkan bahwa sudut ujung pahat dan kecepatan makan berpengaruh signifikan terhadap respon kebulatan. Peningkatan sudut ujung pahat dan kecepatan makan akan meningkatkan penyimpangan kebulatan, sehingga agar diperoleh profil kebulatan yang baik, maka perlu menggunakan sudut ujung pahat yang kecil serta kecepatan makan yang rendah.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.