In the past decade, the efficiency of perovskite solar cells quickly increased from 3.8% to 25.2%. The quality of perovskite films plays vital role in device performance. The films fabricated by solution‐process are usually polycrystalline, with significantly higher defect density than that of single crystal. One kind of defect in the films is uncoordinated Pb2+, which is usually generated during thermal annealing process due to the volatile organic component. Another detrimental kind of defect is Pb0, which is often observed during the film fabrication process or solar cell operation. Because the open circuit voltage has a close relation with the defect density, it is thus desirable to passivate these two kinds of defects. Here, a molecule with multiple ligands is introduced, which not only passivates the uncoordinated Pb2+ defects, but also suppresses the formation of Pb0 defects. Meanwhile, such a treatment improves the energy level alignment between the valence band of perovskite and the highest occupied molecular orbital of spiro‐OMeTAD. As a result, the performance of perovskite solar cells significantly increases from 19.0% to 21.4%.

In addition to high efficiencies, upscaling and long‐term operational stability are key pre‐requisites for moving perovskite solar cells toward commercial applications. In this work, a strategy to fabricate large‐area uniform and dense perovskite films with a thickness over one‐micrometer via a two‐step coating process by introducing NH4Cl as an additive in the PbI2 precursor solution is developed. Incorporation of NH4Cl induces the formation of the intermediate phases of x[NH4+]·[PbI2Clx]x− and HPbI3−xClx, which can effectively retard the crystallization rate of perovskite leading to uniform and compact full‐coverage perovskite layers across large areas with high crystallinity, large grain sizes, and small surface roughness. The 5 × 5 and 10 × 10 cm2 perovskite solar modules (PSMs) based on this method achieve a power conversion efficiency (PCE) of 14.55% and 10.25%, respectively. These PSMs also exhibit good operational stability with a T80 lifetime (the time during which the solar module PCE drops to 80% of its initial value) under continuous light illumination exceeding 1600 h (5 × 5 cm2) and 1100 h (10 × 10 cm2), respectively.

This paper describes a microdroplet merging device that can actively control the merging of various droplets under a wide range of flow conditions, using a simple structure. The microdroplets were trapped and merged in a wide chamber divided by pillars, and their behavior was controlled by two horizontal pneumatic microactuators. Hydrodynamic flow control by the actuation was evaluated numerically, and the trapping and merging of droplets were achieved experimentally and controlled via pressure applied to the microactuators. Furthermore, two independently generated droplets were merged under four different modes, ranging from no merging to four-droplet merging, with different ratios and volumes. The pneumatic actuators allowed not only the control of the number of merged droplets, but also a wide range of applied droplet volumes. The device was fabricated simply using a single-layer PDMS (polydimethylsiloxane) structure, and the continuous merging performance operated using only hydrodynamic flow control without any surfactant. Finally, chemical synthesis of a metal complex was performed by the droplet merging method. Crystallization of the complex was visualized in real time, and the synthesis was verified by ultraviolet-visible spectroscopy.

Incorporation of a certain amount of Cl ions into methylammonium lead iodide (MAPbI3) perovskite films and how these incorporated Cl ions affect the structural and electronic properties of these films...

All-inorganic halide perovskites are promising materials for optoelectronic applications. The surface or interface structure of the perovskites plays a crucial role in determining the optoelectronic conversion efficiency, as well as the material stability. A thorough understanding of surface atomic structures of the inorganic perovskites and their contributions to their optoelectronic properties and stability is lacking. Here we show a scanning tunneling microscopy investigation on the atomic and electronic structure of CsPbBr 3 perovskite. Two different surface structures with a stripe and an armchair domain are identified, which originates from a complex interplay between Cs cations and Br anions. Our findings are further supported and correlated with density functional theory calculations and photoemission spectroscopy measurements. The stability evaluation of photovoltaic devices indicates a higher stability for CsPbBr 3 in comparison with MAPbBr 3 , which is closely related to the low volatility of Cs from the perovskite surface.