Aceclofenac-loaded poly(vinyl-pyrrolidone)-based nanofiber formulations were prepared by electrospinning to obtain drug-loaded orally disintegrating webs to enhance the solubility and dissolution rate of the poorly soluble anti-inflammatory active that belongs to the BCS Class-II. Triethanolamine-containing ternary composite of aceclofenac-poly(vinyl-pyrrolidone) nanofibers were formulated to exert the synergistic effect on the drug-dissolution improvement. The composition and the electrospinning parameters were changed to select the fibrous sample of optimum fiber characteristics. To determine the morphology of the nanofibers, scanning electron microscopy was used. Fourier transform infrared spectroscopy (FT-IR), and differential scanning calorimetry (DSC) were applied for the solid-state characterization of the samples, while the drug release profile was followed by the in vitro dissolution test. The nanofibrous formulations had diameters in the range of few hundred nanometers. FT-IR spectra and DSC thermograms indicated the amorphization of aceclofenac, which resulted in a rapid release of the active substance. The characteristics of the selected ternary fiber composition (10 mg/g aceclofenac, 1% w/w triethanolamine, 15% w/w PVPK90) were found to be suitable for obtaining orally dissolving webs of fast dissolution and potential oral absorption.
The electrospun nanofiber-based orally dissolving webs are promising candidates for rapid drug release, which is due to the high surface area to volume ratio of the fibers and the high amorphization efficacy of the fiber formation process. Although the latter is responsible for the physical and/or chemical instability of these systems. The primary aim of the present study was to elucidate how the addition of polysorbate 80 (PS80) and hydroxypropyl-β-cyclodextrin (HP-β-CD) influenced the electrospinning process, the properties, and the behavior of the obtained nanofibers. In order to reveal any subtle changes attributable to the applied excipients, the prepared samples were subjected to several state of the art imaging and solid state characterization techniques at both macroscopic and microscopic levels. Atomic force microscopy (AFM) revealed the viscoelastic nature of the fibrous samples. At relatively low forces mostly elastic deformation was observed, while at higher loads plasticity predominated. The use of polysorbate led to about two times stiffer, less plastic fibers than the addition of cyclodextrin. The H-C nuclear magnetic resonance (NMR) cross-polarization build-up curves pointed out that cyclodextrin acts as an inner, while polysorbate acts as an outer plasticizer and, due to its "liquid-like" behavior, can migrate in the polymer-matrix, which results in the less plastic behavior of this formulation. Positron annihilation lifetime spectroscopy (PALS) measurements also confirmed the enhanced mobility of the polysorbate and the molecular packing enhancer properties of the cyclodextrin. Solid-state methods suggested amorphous precipitation of the active ingredient in the course of the electrospinning process; furthermore, the nature of the amorphous systems was verified by NMR spectroscopy, which revealed that the use of the examined additives enabled the development of a molecularly dispersed systems of different homogeneities. An accelerated stability study was carried out to track physical state related changes of the incorporated drug and the polymeric carrier. Recrystallization of the active ingredient could not be observed, which indicated a large stress tolerance capacity, but time-dependent microstructural changes were seen in the presence of polysorbate. Raman mapping verified homogeneous drug distribution in the nanofibrous orally dissolving webs. The performed dissolution study indicated that the drug dissolution from the fibers was rapid and complete, but the formed stronger interaction in the case of the PVA-CD-MH system resulted in a little bit slower drug release, compared to the PS80 containing formulation. The results obviously show that the complex physicochemical characterization of the polymer-based fibrous delivery systems is of great impact since it enables the better understanding of material properties including the supramolecular interactions of multicomponent systems and consequently the rational design of drug-loaded nanocarriers of required stability.
3D printing is attracting considerable interest for its capacity to produce prototypes and small production runs rapidly. Fused deposit modeling (FDM) was used to produce polyvalent test plates for investigation of the physical, chemical, and in-vitro biological properties of printed materials. The polyvalent test plates (PVTPs) are poly-lactic acid cylinders, 14 mm in diameter and 3 mm in height. The polymer ester backbone was surface modified by a series of ramified and linear oligoamines to increase its hydrophilicity and introduce a positive charge. The chemical modification was verified by FT-IR spectroscopy, showing the introduction of amide and amine functions, and contact angle measurements confirmed increased hydrophilicity. Morphology studies (SEM, optical microscopy) indicated that the modification of PVTP possessed a planar morphology with small pits. Positron annihilation lifetime spectroscopy demonstrated that the polymeric free volume decreased on modification. An MTT-based prolonged cytotoxicity test using Caco-2 cells showed that the PVTPs are non-toxic at the cellular level. The presence of surface oligoamines on the PVTPs reduced biofilm formation by Candida albicans SC5314 significantly. The results demonstrate that 3D printed objects may be modified at their surface by a simple amidation reaction, resulting in a reduced propensity for biofilm colonization and cellular toxicity.
The enantiomers of vildagliptin, an orally available and selective dipeptidyl-peptidase-4 inhibitor used for the treatment of type II diabetes, have been separated by CD-modified CZE, using uncoated fused-silica capillary. After screening 13 negatively charged CD derivatives as potential chiral selectors, sulfobutyl-ether-α-CD (SBE-α-CD) was selected for the enantioseparation. For the optimization, a factorial analysis study was performed by orthogonal experimental design. Six experimental factors were chosen as variable parameters: temperature, applied voltage, chiral selector and BGE concentrations, pH, and the parameters of the hydrodynamic injection. The optimized system still was not considered final as the second peak (S-enantiomer) migrated too close to the EOF, resulting in a potential inaccuracy during the determination of the chiral impurity. To fine-tune the method "one factor at a time" variation approach was applied. The final method (applying 15°C capillary temperature, 40 mbar × 4 s hydrodynamic injection, 25 kV voltage in 75 mM acetate-Tris buffer [pH 4.75] containing 20 mM SBE-α-CD as chiral selector) was validated according to the ICH guideline. RSD percentage of the resolution value, migration times, and corrected peak areas were below 5% during testing repeatability and intermediate precision. LOD and LOQ values were found to be 2.5 and 7.5 μg/mL, respectively. The method is considered linear in the 7.5-180 μg/mL range for the R-enantiomer. The robustness of the method was justified using Plackett-Burmann statistical experimental design.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.