The objective was to evaluate performance, strengths, and limitations of the microfluidic resistive pulse sensing (MRPS) technique for the characterization of particles in the size range from about 50 to 2000 nm. MRPS, resonant mass measurement (RMM), nanoparticle tracking analysis (NTA) and dynamic light scattering were compared for the analysis of nanometer-sized polystyrene (PS) beads, liposomes, bacteria, and protein aggregates. An electrical conductivity of at least 3 mS/cm (equivalent to 25 mM NaCl) was determined as a key requirement for reliable analysis with MRPS. Particle size distributions of PS beads determined by MRPS, NTA, and RMM correlated well. However, counting precision varied significantly among the techniques and was best for RMM followed by MRPS and NTA. As determined by measuring single and mixed PS bead populations, MRPS showed the highest peak resolution for sizing. RMM and MRPS were superior over dynamic light scattering and NTA for the characterization of stressed protein samples. Finally, MRPS proved to be the only analytical technique able to characterize both bacteria and liposomes. In conclusion, MRPS is an orthogonal technique alongside other established techniques for a comprehensive analysis of a samples particle size distribution and particle concentration.

Polysorbate 80 (PS80) is a commonly used surfactant in therapeutic protein formulations to mitigate adsorption and interface-induced protein aggregation. Several PS80 grades and qualities are available on the market for parenteral application. The role of PS80 grade on protein stability remains debatable, and the impact of (partially) degraded PS on protein aggregation is not yet well understood. In our study, a monoclonal antibody (IgG) was subjected to 3 different mechanical stress conditions in the presence of multicompendial (MC) and Chinese pharmacopeia (ChP) grade PS80. Furthermore, IgG formulations were spiked with (partly) hydrolyzed PS80 to investigate the effect of PS80 degradants on protein stability. PS80 functionality was assessed by measuring the extent of protein aggregation and particle formation induced during mechanical stress by using size-exclusion chromatography, dynamic light scattering, backgrounded membrane imaging, and flow imaging microscopy. No distinguishable differences in PS80 functionality between MC and ChP grade were observed in the 3 stress tests. However, with increasing degree of PS80 hydrolysis, higher counts of subvisible particles were measured after stress. Furthermore, higher levels of PS80 degradants at a constant PS80 concentration may destabilize the IgG. In conclusion, MC and ChP grade PS80 are equally protective, but PS80 degradants compromise IgG stability.

Tuberculosis (TB) is a global disease that is becoming more difficult to treat due to the emergence of multidrug resistant (MDR) Mycobacterium tuberculosis. Inhalable antimicrobial peptides (AMPs) are potentially useful alternative anti-TB agents because they can overcome resistance against classical antibiotics, reduce systemic adverse effects, and achieve local targeting. The aims of the current study were to produce inhalable dry powders containing d-enantiomeric AMPs (D-LAK120-HP13 and D-LAK120-A) and evaluate their solid state properties, aerosol performance, and structural conformation. These two peptides were spray dried with mannitol as a bulking agent at three mass ratios (peptide:mannitol 1:99, 1:49, and 1:24) from aqueous solutions. The resultant particles were spherical, with those containing D-LAK120-HP13 being more corrugated than those with D-LAK120-A. The median volumetric diameter of the particles was approximately 3μm. The residual water content of all powders were <3% w/w and crystalline, due to the low hygroscopicity and crystallinity of mannitol, respectively. The mannitol changed from a mixture of alpha- and beta-forms to delta form with an increasing proportion of AMP in the formulation. The emitted fraction and fine particle fraction of the powders when dispersed from an Osmohaler(®) at 90L/min were about 80% and 50-60% of the loaded dose, respectively, indicating good aerosol performance. Circular dichroism data showed that D-LAK120-HP13 dissolved in Tris buffer at pH 7.15 was of a disordered conformation. In contrast, D-LAK120-A showed greater α-helical conformation. Since the conformations of the AMPs were comparable to the controls (unprocessed peptides), the spray drying process did not substantially affect their secondary structures. In conclusion, spray dried powders containing d-enantiomeric AMPs with preserved secondary molecular structures and good aerosol performance could be successfully produced. They may potentially be used for treating MDR-TB when delivered by inhalation.