Tissue engineering approaches in nerve regeneration often aim to improve results by bridging nerve defects with conduits that mimic key features of the nerve autograft. One such approach uses Schwann cell self-alignment and stabilization within collagen gels to generate engineered neural tissue (EngNT). In this study, we investigated whether a novel blend of fibrin and collagen could be used to form EngNT, as before EngNT design a beneficial effect of fibrin on Schwann cell proliferation was observed. A range of blend formulations was tested in terms of mechanical behavior (gel formation, stabilization, swelling, tensile strength, and stiffness), and lead formulations were assessed in vitro. A 90% collagen 10% fibrin blend was found to promote SCL4.1/F7 Schwann cell viability and supported the formation of aligned EngNT, which enhanced neurite outgrowth in vitro (NG108 cells) compared to formulations with higher and lower fibrin content. Initial in vivo tests in an 8 mm rat sciatic nerve model using rolled collagen-fibrin EngNT rods revealed a significantly enhanced axonal count in the midsection of the repair, as well as in the distal part of the nerve after 4 weeks. This optimized collagen-fibrin blend therefore provides a novel way to improve the capacity of EngNT to promote regeneration following peripheral nerve injury.

Artificial tissues constructed from therapeutic cells offer a promising approach for improving the treatment of severe peripheral nerve injuries. In this study the effectiveness of using CTX0E03, a conditionally immortalised human neural stem cell line, as a source of allogeneic cells for constructing living artificial nerve repair tissue was tested. CTX0E03 cells were differentiated then combined with collagen to form engineered neural tissue (EngNT-CTX), stable aligned sheets of cellular hydrogel. EngNT-CTX sheets were delivered within collagen tubes to repair a 12 mm sciatic nerve injury model in athymic nude rats. Autologous nerve grafts (autografts) and empty tubes were used for comparison. After 8 weeks functional repair was assessed using electrophysiology. Further, detailed histological and electron microscopic analysis of the repaired nerves was performed. Results indicated that EngNT-CTX supported growth of neurites and vasculature through the injury site and facilitated reinnervation of the target muscle. These findings indicate for the first time that a clinically validated allogeneic neural stem cell line can be used to construct EngNT. This provides a potential ‘off the shelf’ tissue engineering solution for the treatment of nerve injury, overcoming the limitations associated with nerve autografts or the reliance on autologous cells for populating repair constructs.

Objective. Gel aspiration-ejection (GAE) has recently been developed for the rapid production of dense, anisotropic collagen gel scaffolds with adjustable collagen fibrillar densities. In this study, a GAE system was applied to produce aligned Schwann cells within a type-1 collagen matrix to generate GAE-engineered neural tissues (GAE-EngNT) for potential nerve tissue engineering applications. Approach. The stability and mechanical properties of the constructs were investigated along with the viability, morphology and distribution of Schwann cells. Having established the methodology to construct stable robust Schwann cell-loaded engineered neural tissues using GAE (GAE-EngNTs), the potential of these constructs in supporting and guiding neuronal regeneration, was assessed both in vitro and in vivo. Main results. Dynamic mechanical analysis strain and frequency sweeps revealed that the GAE-EngNT produced via cannula gauge number 16G (~1.2 mm diameter) exhibited similar linear viscoelastic behaviors to rat sciatic nerves. The viability and alignment of seeded Schwann cell in GAE-EngNT were maintained over time post GAE, supporting and guiding neuronal growth in vitro with an optimal cell density of 2.0×10 6 cells/ml. An in vivo test of the GAE-EngNTs implanted within silicone conduits to bridge a 10 mm gap in rat sciatic nerves for 4 weeks revealed that the constructs significantly promoted axonal regeneration and vascularization across the gap, as compared to the empty conduits although less effective regeneration compared to the autograft groups. Significance. Therefore, this is a promising approach for generating anisotropic and robust engineered tissue which can be used with Schwann cells for peripheral nerve repair.

This study explored different approaches to preserve engineered neural tissue (EngNT), a stabilized, cellular collagen hydrogel containing columns of aligned Schwann cells for nervous system repair. The ability to preserve EngNT without disrupting cellular and extracellular components and structures is important for clinical translation and commercialization. Stabilized cellular gels and EngNT constructs were preserved under various conditions and cell survival assessed using live/dead microscopy and metabolic assay. Optimal survival was recorded in hypothermic (4°C) conditions for 2–3 days using Hibernate®-A media and, for longer-term cryogenic storage (liquid nitrogen), using a mixture of 60% Dulbecco's modified Eagle's medium, 30% fetal bovine serum, and 10% dimethyl sulfoxide. Functionality and structure of preserved EngNT were assessed in coculture with dorsal root ganglion neurons, which indicated that alignment of Schwann cells and the ability of EngNT to support and guide neuronal regeneration were not disrupted. The identification of conditions that preserve EngNT will inform development of storage and transport methodologies to support clinical and commercial translation of this technology and other therapies based on cellular hydrogels.

Inkjet printing (IJP) is an emerging technology for the precision dosing of medicines. We report, for the first time, the printing of the antifungal drug terbinafine hydrochloride directly onto nails for the treatment of onychomycosis. A commercial cosmetic nail printer was modified by removing the ink from the cartridge and replacing it with an in-house prepared drug-loaded ink. The drug-loaded ink was designed so that it was comparable to the commercial ink for key printability properties. Linear drug dosing was shown by changing the lightness of the colour selected for printing (R2 = 0.977) and by printing multiple times (R2 = 0.989). The drug loads were measured for heart (271 µg), world (205 µg) and football (133 µg) shapes. A disc diffusion assay against Trpytophan rubrum showed inhibition of fungal growth with printed-on discs. In vitro testing with human nails showed substantial inhibition with printed-on nails. Hence, this is the first study to demonstrate the ability of a nail printer for drug delivery, thereby confirming its potential for onychomycosis treatment.

No abstract