Chemical recycling is one of the most promising technologies that could contribute to circular economy targets by providing solutions to plastic waste; however, it is still at an early stage of development. In this work, we describe the first light-driven, acid-catalyzed protocol for chemical recycling of polystyrene waste to valuable chemicals under 1 bar of O 2 . Requiring no photosensitizers and only mild reaction conditions, the protocol is operationally simple and has also been demonstrated in a flow system. Electron paramagnetic resonance (EPR) investigations and density functional theory (DFT) calculations indicate that singlet oxygen is involved as the reactive oxygen species in this degradation process, which abstracts a hydrogen atom from a tertiary C–H bond, leading to hydroperoxidation and subsequent C–C bond cracking events via a radical process. Notably, our study indicates that an adduct of polystyrene and an acid catalyst might be formed in situ, which could act as a photosensitizer to initiate the formation of singlet oxygen. In addition, the oxidized polystyrene polymer may play a role in the production of singlet oxygen under light.

We report the development of in situ (online) EPR and coupled EPR/NMR methods to study redox flow batteries, which are applied here to investigate the redox-active electrolyte, 2,6-dihydroxyanthraquinone (DHAQ). The radical anion, DHAQ 3−• , formed as a reaction intermediate during the reduction of DHAQ 2− , was detected and its concentration quantified during electrochemical cycling. The fraction of the radical anions was found to be concentration-dependent, the fraction decreasing as the total concentration of DHAQ increases, which we interpret in terms of a competing dimer formation mechanism. Coupling the two techniquesEPR and NMRenables the rate constant for the electron transfer between DHAQ 3−• and DHAQ 4− anions to be determined. We quantify the concentration changes of DHAQ during the "high-voltage" hold by NMR spectroscopy and correlate it quantitatively to the capacity fade of the battery. The decomposition products, 2,6-dihydroxyanthrone and 2,6-dihydroxyanthranol, were identified during this hold; they were shown to undergo subsequent irreversible electrochemical oxidation reaction at 0.7 V, so that they no longer participate in the subsequent electrochemistry of the battery when operated in the standard voltage window of the cell. The decomposition reaction rate was found to be concentration-dependent, with a faster rate being observed at higher concentrations. Taking advantage of the inherent flow properties of the system, this work demonstrates the possibility of multi-modal in situ (online) characterizations of redox flow batteries, the characterization techniques being applicable to a range of electrochemical flow systems.

The oxidative cleavage of CC double bonds with molecular oxygen to produce carbonyl compounds is an important transformation in chemical and pharmaceutical synthesis. In nature, enzymes containing the first-row transition metals, particularly heme and non-heme iron-dependent enzymes, readily activate O 2 and oxidatively cleave CC bonds with exquisite precision under ambient conditions. The reaction remains challenging for synthetic chemists, however. There are only a small number of known synthetic metal catalysts that allow for the oxidative cleavage of alkenes at an atmospheric pressure of O 2 , with very few known to catalyze the cleavage of nonactivated alkenes. In this work, we describe a light-driven, Mn-catalyzed protocol for the selective oxidation of alkenes to carbonyls under 1 atm of O 2 . For the first time, aromatic as well as various nonactivated aliphatic alkenes could be oxidized to afford ketones and aldehydes under clean, mild conditions with a first row, biorelevant metal catalyst. Moreover, the protocol shows a very good functional group tolerance. Mechanistic investigation suggests that Mn−oxo species, including an asymmetric, mixed-valent bis(μ-oxo)-Mn(III,IV) complex, are involved in the oxidation, and the solvent methanol participates in O 2 activation that leads to the formation of the oxo species.

In situ electrochemical electron paramagnetic resonance (EPR) spectroscopy is used to understand the mixed lithiation/deposition behavior on graphite anodes during the charging process. The conductivity, degree of lithiation, and the deposition process of the graphite are reflected by the EPR spectroscopic quality factor, the spin density, and the EPR spectral change, respectively. Classical over‐charging (normally associated with potentials ≤0 V vs. Li+/Li) are not required for Li metal deposition onto the graphite anode: Li deposition initiates at ca. +0.04 V (vs. Li+/Li) when the scan rate is lowered to 0.04 mV s−1. The inhibition of Li deposition by vinylene carbonate (VC) additive is highlighted by the EPR results during cycling, attributed to a more mechanically flexible and polymeric SEI layer with higher ionic conductivity. A safe cut‐off potential limit of +0.05 V for the anode is suggested for high rate cycling, confirmed by the EPR response over prolonged cycling.

Fabrication of heterostructured materials is a strategy to boost the charge-transfer kinetics and the performance of high-rate lithium storage. Here, a facile, lowtemperature method for the synthesis of high-area TiO2 nanospheres containing both anatase and rutile phases is described. The as-prepared materials contain a high concentration of oxygen vacancies facilitating electron conduction in the anatase phase and theoretical calculations provide evidence of a low energy barrier for Li + transport in the rutile phase. The synergy between the two phases renders the shared conduction of electrons through anatase and Li + ions via rutile at high-current rates, leading to the anodes that outperform the alternate TiO2 systems when the combination of capacity at high current densities and cycle stability are considered, displaying a capacity of 95.4 mAh g-1 at 10 A g-1 and a 97.2 % retention of capacity over 500 cycles at 1 A g-1 .