Wood machining is one of important utilization properties, especially for lesser known wood species. This paper determines the machining properties and possible utilization of punak (Tetramerista glabra Miq.), meranti bunga (Shorea teysmanniana Dryer ex Brandis), mempisang (Alphonsea spp.), suntai (Palaquium burckii H.J.L.), and pasak linggo (Aglaia argentea Blume) originated from Riau Province. The tests were conducted based on the modified testing standard of ASTM D-1666-64. Twenty samples of each species were machining tested for the work of planing, shaping, boring, turning, and sanding. Visual observation was performed using loupe 10x magnification. Research revealed that planing, shaping, boring, turning and sanding properties were significantly influenced by wood species. Punak and pasak linggo had good and very good machining properties. Mempisang had a wide range machining properties from poor to very good, while meranti bunga had poor to good machining properties. Lastly, suntai had a moderate to good machining properties. Regression analysis showed that higher specific gravity resulted in better machining properties. Wood with good to very good categories could be suggested as raw materials for various products. Mempisang and meranti bunga should be carefully handled, particularly in boring and turning processes.
The increase use of wood products for outdoor arises from warmth color and amenity properties of wood. However, wood is naturally degraded in term of color changes and finishing layer percentage after outdoor exposure. This paper presents wood color change and finishing layer durabillity after one year outdoor exposure. Five lesser known wood species from Riau were coated transparently using acrylic, enamel, polyurethane, ultran lasur ultra violet (UV), and ultran politur P-03 UV prior to outdoor exposure. Wood color differences were assessed according to CIELab system and coating film coverages were digitally analyzed by ImageJ software. The result showed that natural wood color turned into greyish pale after one year outdoor exposure. Color changes are relatively high in the first month then moderate and little changes every month there of. Finished layer wood samples were more resistant to weathering than unfinished surfaces. Finishing material of enamel (ET), lasur (LSR), and P03 (PP) experienced better coverage than acrylic and polyurethane finish. Finishing layer is gradually degraded, then re-finishing is necessary for optimal outdoor protection. Relationships between finishing coverage and color change showed medium correlation, where the greater finishing coverage, the greater the color changes.
ABSTRAKPenelitian ini bertujuan untuk mengetahui pengaruh jenis kayu dan jumlah lapisan venir terhadap sifat venir lamina. Jenis kayu yang digunakan terdiri dari sengon, pinus, dan campuran sengon dengan pinus. Dibuat venir lamina dengan jumlah lapisan bervariasi, yaitu 4, 6, dan 8 lapis. Variasi jumlah lapisan bertujuan agar dapat diketahui mutu venir lamina yang dihasilkan dari berbagai variasi jumlah lapisan tersebut. Perekat yang digunakan adalah urea formaldehida (UF) cair. Hasil penelitian menunjukkan bahwa rata-rata kadar air venir lamina 10,76%, kerapatan 0,54 g/cm 3 PENDAHULUANHutan merupakan sumber daya alam yang penting, dengan salah satu hasilnya berupa kayu. Sebagian besar pasokan kayu untuk industri pengolahan kayu di Indonesia berasal dari hutan alam. Akan tetapi kemampuan hutan alam dalam memasok kebutuhan bahan baku kayu terus menurun sehingga terjadi kekurangan bahan baku kayu dalam jumlah yang cukup besar. Balfas (2010) menyatakan bahwa dalam kebanyakan forum komunikasi ilmiah dilaporkan defisit kayu nasional akan mencapai lebih dari 50 juta m 3 /tahun. Fenomena seperti ini dapat dilihat di pasaran, yaitu semakin sulitnya dijumpai kayu-kayu olahan dari berbagai jenis kayu yang biasa diperdagangkan (jenis kayu komersial). Untuk mengatasi masalah ini, pemerintah telah melakukan berbagai upaya diantaranya dengan mendorong penanaman jenis-jenis kayu cepat tumbuh (fast-growing species) seperti mangium, sengon, rasamala, gmelina, jabon, dan lain-lain melalui pembangunan hutan tanaman, baik berupa hutan tanaman industri (HTI) maupun hutan rakyat (HR). Kedepannya diharapkan keberadaan kayu dari hutan tanaman dapat mensubstitusi kekurangan pasokan kayu dari hutan alam.Kayu yang berasal dari hutan tanaman sebagian besar memiliki diameter kecil. Kondisi kayu seperti ini bila langsung diolah akan menghasilkan papan dan balok gergajian dengan ukuran dimensi yang sempit, sehingga memiliki keterbatasan dalam pemanfaatannya. Untuk mengatasi hal ini, dolok kayu dapat dikupas dengan menggunakan mesin kupas menghasilkan lembaran-lembaran tipis yang disebut dengan venir.Venir lamina (Laminated veneer lumber (LVL)) adalah produk yang dibuat dengan cara merekatkan lapisan-lapisan venir dengan menggunakan perekat dengan arah sejajar serat. Dalam hal tertentu juga diperkenankan adanya venir silang di bawah venir luar (SNI 2000). Pembuatan venir lamina umumnya untuk pengganti kayu gergajian berupa papan dan balok (Sylvina et al. 2002). Venir lamina selain mem-
ABSTRAKTulisan ini mengemukakan hasil studi sifat pemesinan beserta kemungkinan pemanfatannya berdasarkan sifatsifat tersebut. Pengamatan dilakukan terhadap lima jenis kayu, yaitu kayu marasi (Hymenaea sp.), asam jawa (Tamarmaus indica), ki keuyeup (Enonimus javanica), cantigi (Pempis acidula), dan kendal (Euretia acuminate R.) asal Jawa Barat. Hasil penelitian menunjukkan bahwa sifat penyerutan, pembentukan, pemboran, pembubutan, dan pengampelasan kelima jenis kayu secara nyata dipengaruhi oleh jenis kayu. Mutu pemesinan kayu asam jawa, marasi, dan ki keuyeup termasuk baik sampai sangat baik, sedangkan kayu cantigi dan kendal termasuk sedang sampai baik. Terdapat kecenderungan semakin tinggi berat jenis kayu, semakin baik sifat pemesinannya. Kelima jenis kayu dapat disarankan untuk diolah menjadi beragam produk pengerjaan dengan hasil pemesinan baik sampai sangat baik, kecuali kayu cantigi dan kendal jika memerlukan proses pembubutan harus dilakukan dengan lebih hati-hati.Kata kunci: berat jenis, jenis kayu kurang dikenal, sifat pemesinan ABSTRACT This paper deals with a study in machining properties of five wood species, i.e. marasi (Hymenaea sp.), asam jawa (Tamarmaus indica), ki keuyeup (Enonimus javanica), cantigi (Pempis acidula), and Kendal (Euretia acuminate R.) from West Java. The result revealed that planing, shaping, boring, turning, and sanding properties were significantly affected by wood species. The machining qualities of asam jawa, marasi and ki keuyeup woods with respect to criteria were good to very good, while those cantigi and Kendal fair to good. There is a tendency of the higher density of wood, the better of machining properties. These five of wood can be suggested to be processed into various products processing with machining results as good to very good, except cantigi and kendal if need turning process must be done more carefully.Keywords: lesser known wood species, machining properties, specific gravity PENDAHULUAN Kemampuan hutan alam dalam memasok kebutuhan bahan baku kayu untuk industri pengolahan kayu di Indonesia terus menurun sehingga terjadi kekurangan bahan baku kayu dalam jumlah yang cukup besar. Balfas (2010) menyatakan, bahwa dalam kebanyakan forum komunikasi ilmiah dilaporkan defisit kayu nasional akan mencapai lebih dari 50 juta m 3 / tahun. Fenomena seperti ini dapat dilihat di pasaran, yaitu semakin sulitnya dijumpai kayu-kayu olahan dari berbagai jenis kayu yang biasa diperdagangkan (jenis kayu komersial). Dalam kondisi seperti ini, pemanfaatan kayu tidak dapat hanya mengandalkan jenis-jenis kayu komersial. Menurut Martawijaya et al. (1998), selain jenis-jenis kayu yang telah biasa dikenal dalam perdagangan kayu sebagai kayu perdagangan, terdapat 133 jenis kayu lainnya yang digolongkan ke dalam kelompok kayu kurang dikenal.Jenis-jenis kayu kurang dikenal perlu terlebih dahulu dipelajari sifat dasarnya. Pengetahuan tentang sifat dasar dapat mengarahkan tujuan pemanfaatan suatu jenis kayu agar diperoleh efisiensi penggunaan jenis kayu tersebut, sehingga dapat menggantik...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.